RK3288[android 7.1]调试笔记 ----双屏同显（edp屏做主屏，lvds做副屏）

最新推荐文章于 2024-06-07 14:48:08 发布

转载最新推荐文章于 2024-06-07 14:48:08 发布 · 3.4k 阅读

收录于

RK3288

本文详细介绍了如何在RK3288平台上配置EDP和LVDS双屏显示，通过修改rk3288-evb-android-rk808-edp.dts文件，设置EDP和LVDS屏的参数，实现双屏同时显示的功能。

1 找到在要编译的rk3288-evb-android-rk808-edp.dts
调试思路先将edp和lvds屏配置其dts分别点亮后，最后将两个屏的dts合在一起
在rk3288-evb-android-rk808-edp.dts中加上最终的edp屏和lvds屏的dts配置如下：

。。。。。。。。。。。
// added for edp start <<<
&edp {
	status = "okay";
};

&edp_phy {
	status = "okay";
};
 &route_edp {
	status = "okay";
};
//rk3288 有两路通道vopb(4K) vopl(2K) ,这里同显设vopb通道是edp,vopl通道是lvds
&edp_in_vopb {
	status = "okay";
};
&edp_in_vopl {
	status = "disabled";
};
&edp_panel {
//	compatible = "simple-panel";
    compatible ="lg,lp079qx1-sp0v";
//	backlight = <&backlight>;  //这里同显如果共用背光，只需要配置一个背光
	power-supply = <&vcc_lcd>;
	status = "okay";

	disp_timings: display-timings {
		native-mode = <&edp_panel_name>;

		edp_panel_name: timing0 {
			clock-frequency = <158000000>;
			hactive = <1920>;
			vactive = <1080>;
			hfront-porch = <48>;
			hsync-len = <4>;
			hback-porch = <310>;
			vfront-porch = <3>;
			vsync-len = <4>;
			vback-porch = <60>;
			hsync-active = <0>;
			vsync-active = <0>;
			de-active = <0>;
			pixelclk-active = <0>;
		};
	};
};

// added edp end >>>

// added  for lvds start <<<



&route_lvds {
	status = "okay";
};

&lvds {
	status = "okay";
};
//rk3288 有两路通道vopb(4K) vopl(2K) ,这里同显设vopb通道是edp,vopl通道是lvds
&lvds_in_vopl {
	status = "okay";
};

&lvds_in_vopb {
	status = "disabled";
};

&lvds_panel {
	status = "okay";
	compatible ="simple-panel";
	backlight = <&backlight>;   //这里同显如果共用背光，只需要配置一个背光
//	bus-format = <MEDIA_BUS_FMT_RGB666_1X18>; <MEDIA_BUS_FMT_RGB888_1X24>;
//	bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
	enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
//	enable = <&gpio7 3 GPIO_ACTIVE_HIGH>;
	enable-delay-ms = <10>;
//	power-supply = <&vcc_lcd>;
	rockchip,data-mapping = "vesa";
//	rockchip,data-mapping = "jeida";
	rockchip,data-width = <24>;
	rockchip,output = "duallvds";

	display-timings {
		native-mode = <&lvds_panel_name>;
		lvds_panel_name: timing0 {
			creen-type = <SCREEN_DUAL_LVDS>;
			lvds-format = <LVDS_8BIT_2>;
			out-face    = <OUT_P888>;
			clock-frequency = <148000000>;
			hactive = <1920>;
			vactive = <1080>;
			hback-porch = <100>;
			hfront-porch = <160>;
			vback-porch = <25>;
			vfront-porch = <10>;
			hsync-len = <1>;
			vsync-len = <1>;
			hsync-active = <20>;
			vsync-active = <10>;
			de-active = <0>;
			pixelclk-active = <0>;
		};
	};
};

// added lvds end <<<
。。。。。。。。。。。