<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0" xmlns:cc="http://cyber.law.harvard.edu/rss/creativeCommonsRssModule.html">
    <channel>
        <title><![CDATA[Stories by Analogy on Medium]]></title>
        <description><![CDATA[Stories by Analogy on Medium]]></description>
        <link>https://medium.com/@analogydesign?source=rss-991a19e7be1f------2</link>
        <image>
            <url>https://cdn-images-1.medium.com/fit/c/150/150/1*ckCQHH1_X5RtcjWF9lkxXw.png</url>
            <title>Stories by Analogy on Medium</title>
            <link>https://medium.com/@analogydesign?source=rss-991a19e7be1f------2</link>
        </image>
        <generator>Medium</generator>
        <lastBuildDate>Fri, 20 Nov 2026 08:56:27 GMT</lastBuildDate>
        <atom:link href="https://medium.com/@analogydesign/feed" rel="self" type="application/rss+xml"/>
        <webMaster><![CDATA[yourfriends@medium.com]]></webMaster>
        <atom:link href="http://medium.superfeedr.com/" rel="hub"/>
        <item>
            <title><![CDATA[Why “We’ll Fix It in the Next Version” Is the Most Expensive Sentence in Hardware]]></title>
            <link>https://analogydesign.medium.com/why-well-fix-it-in-the-next-version-is-the-most-expensive-sentence-in-hardware-a925424f6148?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/a925424f6148</guid>
            <category><![CDATA[manufacturing-processes]]></category>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[product-development]]></category>
            <category><![CDATA[hardware-development]]></category>
            <category><![CDATA[product-design]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Thu, 16 Jul 2026 10:31:21 GMT</pubDate>
            <atom:updated>2026-07-16T10:31:21.101Z</atom:updated>
            <content:encoded><![CDATA[<h3>A founder said it in a Tuesday standup. Six months and $180,000 later, there was no next version to fix it in.</h3><p>He said it first about the hinge.</p><p>It was late 2024, and the product on the table in front of him was held together with a hinge mechanism that felt just slightly loose. It was not broken. The kind of thing you notice, frown at for four seconds, and move past because there’s a demo to prep and a CES badge to print.</p><p>“We’ll tighten it in the next version,” he said.</p><p><strong>Nobody in the room argued. Nobody ever does.</strong> It’s the most reasonable-sounding sentence in hardware, which is exactly what makes it so dangerous.</p><p>Eight months later, the company was acquired. The product that got him there did not have the loose hinge. They were the ones where someone stopped him and asked: what does “next version” actually cost us if this version is the one that ships to CES judges, investors, and the first 500 customers?</p><figure><img alt="Hardware Design: “We’ll Fix It in the Next Version”" src="https://cdn-images-1.medium.com/max/1024/1*Iv0SXfWfeNOzq-b73kfAGA.jpeg" /></figure><p>That question is the whole story.</p><h3>The sentence that sounds like patience and is actually debt.</h3><p>In software, “we’ll fix it in the next version” is basically true. You push a patch. Nobody’s phone catches fire.</p><p>In hardware, the sentence means something else entirely. A tooling change after injection molds are cut isn’t a patch, it’s a new mold, and molds for a mid-complexity plastic housing routinely run into the tens of thousands of dollars. A PCB revision after boards are already fabricated isn’t a patch either, it’s a new spin, a new order, and, depending on your supplier and layer count, another two to six weeks added to a runway that was already tight.</p><p><strong>The “next version” isn’t a version. It’s a new bill.</strong></p><p>This is the gap almost nobody tells first-time hardware founders about, and it’s the one worth sitting with for a second: the cost of fixing something <em>before</em> it’s manufactured and the cost of fixing it <em>after</em> aren’t on the same scale. They’re not even in the same category of expense. One is a design iteration. The other is a redo.</p><h3>What “later” actually costs, in order.</h3><p>Design engineers talk about this using a rule that shows up, in different forms, across manufacturing literature going back to Boeing’s early quality programs: a defect caught at the design stage costs some multiple less to fix than the same defect caught after tooling, and dramatically less than the same defect caught after the product is in a customer’s hands. The exact multiplier gets argued over. The direction never does.</p><p>Here’s what that actually looks like on a founder’s calendar:</p><ul><li><strong>Caught at CAD stage:</strong> a sketch revision, maybe a day, maybe free.</li><li><strong>Caught at prototype stage:</strong> a reprint, a few hundred dollars, a few days.</li><li><strong>Caught after tooling is cut:</strong> a new mold or a modified one, tens of thousands of dollars, four to eight weeks.</li><li><strong>Caught after the product has shipped:</strong> a recall, a warranty wave, or a silent trust problem you won’t see in the data for two quarters.</li></ul><p>Most founders live somewhere in the middle of that list and think they’re still near the top of it.</p><h3>The mistake that isn’t really about the hinge.</h3><p>Analogy Design has watched this pattern often enough that it made the list in their piece on the <a href="https://www.analogydesign.co/blog/hardware-startup-mistakes">most common ways hardware startups die before they ever launch</a>, and skipping design-for-manufacturing review early is right near the top of it. Not because founders are careless. Because “later” always sounds cheaper in the moment than “now.”</p><blockquote>VT Rao, founder of Analogy Design, has a blunt way of putting it: “Every ‘we’ll fix it later’ is a decision to pay a manufacturing bill with a fundraising problem instead of a design one.”</blockquote><p>That line is worth sitting with. Because it reframes what’s actually being deferred. It’s not a hinge. It’s not a button gap. It’s a choice about which version of your company absorbs the cost: the one still iterating on foam and CAD files, or the one that already has a Shark Tank valuation, or a retailer commitment, or a CES badge, riding on the outcome.</p><h3>The backpack that almost shipped soft.</h3><p>There’s a case study that makes this concrete without needing a single spec sheet.</p><p>An ergonomic backpack project, the kind meant to sit against a spine for hours without becoming a problem, had a strap adjustment mechanism that worked fine in the prototype. Fine on a bench. Fine on the three testers who tried it in the studio.</p><p>“Fine in testing” is the second most expensive sentence in hardware, right behind the one in this title.</p><p>The team pulled in ergonomics research before locking the housing geometry: the kind of human-factors literature that consistently shows load-bearing comfort depends less on padding thickness and more on how weight distributes across contact points over time, a finding echoed in decades of occupational ergonomics work going back to early NASA anthropometry studies. That single review, done before tooling, reshaped the strap mechanism. The product went on to Shark Tank. You can read how the geometry actually got locked in <a href="https://www.analogydesign.co/work/ergonomic-backpack">Analogy’s case study on launching the category</a>.</p><p>Nobody claps for the meeting where a strap mechanism got redesigned three weeks before it was supposed to be final. But that meeting is the reason there was a Shark Tank moment to have at all.</p><h3>Why founders say it anyway.</h3><p>Nobody says “we’ll fix it later” because they’re lazy. They say it because at that exact moment, in that exact room, “later” is genuinely the cheaper-<em>feeling</em> option. Fixing it now means a schedule slip founders can see today. Fixing it later means a cost that lives in a future they haven’t budgeted yet, against a bill they haven’t been sent.</p><p>TechCrunch has covered this pattern across dozens of hardware-startup postmortems: the founders who fail rarely fail because the product didn’t work. They fail because the runway ran out three weeks before the version that worked would have shipped. The math was never about the product. It was about which invoice arrived first.</p><p><strong>Hardware doesn’t punish you for moving slow. It punishes you for moving the bill.</strong></p><h3>What “fixing it now” actually means.</h3><p>This isn’t an argument for perfectionism. Analogy’s own process, the one behind 250+ shipped hardware products across clients like Panasonic, Unilever, and Amazon, isn’t built around never shipping with flaws. It’s built around knowing, on purpose, which flaws are allowed to travel to the next version and which ones aren’t.</p><p>That’s the actual skill. Not zero-defect thinking. <strong>Sequencing.</strong></p><p>A tolerance issue that only affects a color variant launching in month six? Fine, defer it. A structural flex in the exact spot a user’s hand grips fifty times a day? That one doesn’t get to wait for a “next version,” because for a lot of hardware products, there isn’t a guaranteed next version. There’s just this one, and whether it earns the runway to build another.</p><p>The teams who get this right treat design-for-manufacturing review the way pilots treat a pre-flight checklist: boring, repetitive, and the reason nothing dramatic happens later. The teams who get it wrong treat it as a formality to speed past on the way to a demo date.</p><h3>The question worth asking before your next standup.</h3><p>So here’s the uncomfortable one, and it’s genuinely worth sitting with rather than answering too fast: the last time your team said “we’ll fix it in the next version,” was that actually true? Was there a next version already funded, tooled, and scheduled? Or was “next version” just a nicer way of saying “future us, please have more money and more time than present us does”?</p><p>Most founders have never actually checked. That’s not a knock. It’s just rarely the first question anyone asks in a room that’s excited about a demo date.</p><p>It might be the only one that matters.</p><p><em>Analogy Design is an industrial design studio in Bangalore that’s shipped 250+ hardware products and helped founders raise $65M+ since. More at </em><a href="https://www.analogydesign.co/"><em>analogydesign.co</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=a925424f6148" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Your Prototype Isn’t Lying to You. Your Assumptions Are.]]></title>
            <link>https://analogydesign.medium.com/your-prototype-isnt-lying-to-you-your-assumptions-are-89bb2e112c2d?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/89bb2e112c2d</guid>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[hardware-prototyping]]></category>
            <category><![CDATA[mvp-development]]></category>
            <category><![CDATA[mvp-development-services]]></category>
            <category><![CDATA[prototyping]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Mon, 13 Jul 2026 04:32:25 GMT</pubDate>
            <atom:updated>2026-07-13T04:32:25.479Z</atom:updated>
            <content:encoded><![CDATA[<h3>Six things almost every hardware founder believes about manufacturing right up until the moment it costs them six figures.</h3><p>A founder once walked into a design studio in Bangalore holding a napkin sketch and a working demo held together with hot glue.</p><p>Eight months later, he was on stage at CES. Not long after that, his company was acquired.</p><p>That founder was got an acquisition offer faster than most startups finish their first fundraise.</p><p>Everyone wants that story. Almost nobody gets it. And the gap between the founders who do and the founders who don’t usually isn’t talent, funding, or even the idea itself.</p><figure><img alt="Your Prototype Isn’t Lying to You. Your Assumptions Are." src="https://cdn-images-1.medium.com/max/1024/1*_X6ty6P5Vzd8UtcnMAkRRA.jpeg" /></figure><p>It’s a handful of assumptions about manufacturing that feel obviously true, and are almost completely wrong.</p><p>Here are six of them.</p><h3>1. “If it works on my desk, it’ll work off the line.”</h3><p>This is the one that kills the most companies, and it kills them quietly.</p><p>A prototype is a proof of concept. It is not a product. The tolerances, the materials, the assembly sequence, even the glue you used to hold two parts together, none of it survives contact with a real factory unless it was designed for one from day one.</p><p>Design for Manufacturing and Assembly, or DFMA, exists specifically because “it worked in the lab” and “it works at 10,000 units” are two completely different engineering problems.</p><p>Founders who skip this step usually find out the hard way, somewhere between the first production run and the first returns spreadsheet.</p><p><em>The prototype is the easy 10%. The other 90% is where startups actually die.</em></p><h3>2. “We’ll figure out the supply chain once we have the design locked.”</h3><p>Backwards. Every single time.</p><p>The world’s first automated chai machine, a product called <a href="https://www.analogydesign.co/work/dostea">Dostea</a>, could not have been designed the way it was without supply chain constraints shaping the engineering from week one. Same with <a href="https://www.analogydesign.co/work/kitchen-stove-agnisumukh">Agnisumukh</a>, the world’s first flame-less commercial stove: the components that made it safe were also the components that made it sourceable at scale.</p><p>Sourcing isn’t a step that happens after design. It’s an input into design.</p><p>The founders who treat it as an afterthought end up redesigning a “finished” product from scratch when they discover the one component they built everything around has a 40-week lead time, or doesn’t exist outside a single factory in a single country.</p><h3>3. “A cheaper factory means a cheaper product.”</h3><p>Here’s the number founders don’t see coming: teams that get manufacturing right the first time see something closer to a 250% return on that investment, not because the factory was cheap, but because they didn’t pay twice.</p><p>The real cost of hardware isn’t the unit price on a quote. It’s the redesign after the first bad batch. It’s the tooling you have to scrap because nobody caught a draft angle issue before the mold was cut. It’s the shipment that gets held at customs because the certification wasn’t planned for.</p><p>A slightly more expensive partner who gets it right once is cheaper than a cheap one you pay three times.</p><blockquote>VT Rao, founder of Analogy Design, puts it simply: “Manufacturing isn’t where you cut costs. It’s where you stop bleeding them.”</blockquote><h3>4. “Ergonomics is a nice-to-have, we’ll add it later.”</h3><p>Try telling that to the team behind <a href="https://www.analogydesign.co/work/massager-backpack-eume">Eume</a>, an ergonomic backpack that went on on Shark Tank. Comfort wasn’t a feature bolted on at the end. It was the entire premise the product was built around.</p><p>There’s real science behind why this matters so much. Human factors research consistently shows that discomfort during even short periods of use measurably changes whether people keep using a product at all, which is a nicer way of saying: uncomfortable products get returned, and comfortable ones get recommended to a friend.</p><p>“Later” for ergonomics almost always means “never,” because by the time a product ships, the tooling is cut and the changes that mattered most are the ones that were cheapest to make in month one.</p><h3>5. “One good industrial designer can do it all.”</h3><p>A single designer can sketch a beautiful product. They cannot, alone, take that sketch through structural engineering, thermal management, regulatory compliance, DFM, tooling design, and a production line without something breaking.</p><p>The products that make it to Panasonic’s shelf, or into Unilever’s supply chain, or onto Wildcraft’s outdoor gear line, go through a process with dozens of specialist checkpoints most founders never see: mechanical engineers, manufacturing engineers, compliance specialists, each catching a different category of failure before it becomes expensive.</p><p>This exact pattern has been seen for years in postmortems of failed hardware launches: it’s rarely the idea that fails. It’s the handoff between disciplines that nobody owned.</p><p><em>A great sketch has never once survived a bad handoff.</em></p><h3>6. “Global manufacturing means our team has to be global too.”</h3><p>Roughly three quarters of the clients behind Analogy Design’s 250+ shipped products, 23 international design awards, and $65 million+ in client funding raised are based in the US and Europe, working with a team headquartered in Bangalore.</p><p>Distance was never the obstacle founders assume it is. Time zones, video calls, and shared CAD files have quietly solved a problem that used to require someone to physically relocate.</p><p>What actually determines whether a remote manufacturing partnership works isn’t geography. It’s whether the other side of that video call has actually shipped hardware before, at scale, through a real factory, not just rendered it beautifully in a pitch deck.</p><p>Six assumptions. Six ways founders quietly pay for a mistake they didn’t know they were making.</p><p>Here’s the uncomfortable question worth sitting with: if your team can’t answer, right now, which of these six you’re currently getting wrong, that’s usually the one that ends up costing the most.</p><p>Which one did you learn the hard way? I’d genuinely like to hear it in the comments.</p><p><em>Analogy Design is an industrial design studio in Bangalore that has taken 250+ hardware products from sketch to shelf for founders across the US, Europe, and Asia. More at </em><a href="https://www.analogydesign.co/"><em>analogydesign.co</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=89bb2e112c2d" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Your Kickstarter Hit $500K. Then Everything Fell Apart.]]></title>
            <link>https://analogydesign.medium.com/your-kickstarter-hit-500k-then-everything-fell-apart-91ec90a58271?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/91ec90a58271</guid>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[startup-lessons]]></category>
            <category><![CDATA[hardware-startup]]></category>
            <category><![CDATA[successful-entrepreneurs]]></category>
            <category><![CDATA[product-development]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Mon, 13 Jul 2026 04:25:40 GMT</pubDate>
            <atom:updated>2026-07-13T04:25:40.553Z</atom:updated>
            <content:encoded><![CDATA[<h3>The five moments after a “successful” launch that quietly decide whether a hardware startup survives its own funders</h3><p>Eight months before CES 2025, a founder had a napkin sketch and no company.</p><p>By the time the show floor lights came on, his revolutionary AI glasses weren’t just a prototype. They were on their way to an acquisition by a large technology firm.</p><p>That’s the version of the crowdfunding story <strong>everyone wants to tell</strong>.</p><p>Here’s the version nobody posts about: the founder who hit his funding goal in 36 hours, popped champagne, and then spent the next year fielding furious emails from 4,000 backers who never got a product.</p><p>The campaign didn’t fail. The campaign <em>worked</em>. <strong>That was the problem.</strong></p><figure><img alt="Your Kickstarter Hit $500K. Then Everything Fell Apart." src="https://cdn-images-1.medium.com/max/1024/1*z7JgM2FgOVhkojOuIXvETw.jpeg" /></figure><p>Hardware crowdfunding has a strange cruelty built into it. Raising the money is the easy part now. Delivering the thing you promised, at the price you promised, on anything close to the timeline you promised, is where most hardware founders discover they built a marketing funnel instead of a manufacturing plan.</p><p>Here are the five moments that quietly implode most campaigns after the confetti falls.</p><h3>1. The prototype that was never meant to be manufactured</h3><p>Somewhere between the Kickstarter video and backer unit #1, there’s a gap almost nobody budgets for.</p><p>The prototype that raised the money was built by hand. One-off. Machined, glued, hot-melted, and lovingly babysat by an engineer who knew exactly which corner to press to make the hinge stop squeaking.</p><p>That object cannot be manufactured 10,000 times.</p><p>Design for Manufacturing (DFM) is not a phase you get to after a successful raise. It’s the reason a successful raise doesn’t turn into a class-action-flavored Reddit thread six months later. Tolerances that were “close enough” on a 3D print become a 12% defect rate at scale. A snap-fit that worked once, by hand, fails at injection-molding volumes because nobody accounted for material shrinkage.</p><p>This is the single most common reason a fully-funded campaign quietly stops posting updates.</p><p><em>“A campaign’s real ship date isn’t decided the day it launches. It’s decided the day the prototype gets handed to manufacturing,”</em> says VT Rao, founder of Analogy Design, the Bangalore-based industrial design studio that has taken 250+ hardware products through this exact handoff.</p><p>If you want the unglamorous version of what this actually looks like: tolerance stacking, material selection, mold flow simulation, and the dozen decisions that happen <em>before</em> a single unit ships, <a href="https://www.analogydesign.co/blog">Analogy’s DFM breakdown</a> is worth the twenty minutes.</p><h3>2. Confusing “fully funded” with “fully costed”</h3><p>A campaign that raises $500K feels like a green light.</p><p>It’s actually a spreadsheet problem wearing a party hat.</p><p>Backers pledge based on a price the founder set months earlier, often before tooling quotes, before certification costs, before the third shipping-container price hike of the year came in. Somewhere in the excitement, “we hit our goal” gets treated as “we have enough money,” and those are almost never the same sentence.</p><p><strong>A campaign hitting 300% of its goal has, on average, told you nothing about whether it can afford to ship.</strong></p><p>Tooling for injection molding alone can run into six figures before a single unit rolls off the line. Certification (FCC, CE, UL, depending on the market) adds weeks and real money. Freight costs that were stable when the campaign launched can shift dramatically by the time containers actually need booking. Anyone who lived through 2021’s shipping rate spikes knows this isn’t hypothetical.</p><p>The founders who survive this stage aren’t the ones who raised the most. They’re the ones who built their Bill of Materials <em>before</em> they set their backer price, not after.</p><h3>3. Falling in love with the CES version, not the shippable version</h3><p>There’s a specific kind of trap that catches ambitious founders: the version of the product that wins a stage demo and the version that can be manufactured at cost are sometimes two different products.</p><p>Beautiful curved glass. A finish that photographs perfectly under trade-show lighting. A sensor placement that looks elegant but adds $40 to per-unit cost the moment you try to actually solder it in at volume.</p><p>Eume’s ergonomic backpack didn’t hit a $4.5M Shark Tank valuation by shipping the flashiest possible version. It hit that number because the ergonomics were engineered to actually work on a human back, repeatedly, at scale, not just to look good in a 90-second pitch.</p><p>Wired and Core77 have both, at various points, covered the graveyard of once-viral hardware products that nailed the demo and collapsed under the weight of their own manufacturing complexity. The pattern is old. It keeps happening anyway, because a demo only has to work once, and a product has to work every single time, for every single backer.</p><h3>4. Treating the supply chain like a detail instead of the whole plot</h3><p>Somewhere around backer update #4, the tone always changes.</p><p>Update #1: “We’re thrilled to announce…” Update #4: “We’ve hit some unexpected sourcing delays…” Update #9: silence.</p><p>A single component (one chip, one connector, one battery cell) with a single supplier and no backup plan is not a supply chain. It’s a hope.</p><p>The founders behind Dostea, the world’s first automated chai machine, and Agnisumukh, the world’s first flame-less commercial stove, weren’t just solving design problems. They were solving “what happens if this one part becomes unavailable in month six” problems, long before a single backer unit needed to ship.</p><p>That’s not a glamorous part of the story. It’s also the part that decides whether there’s a story to tell in twelve months.</p><h3>5. Launching before the story was actually true yet</h3><p>This is the quietest killer, and the hardest one for founders to admit to themselves.</p><p>A campaign page is a promise dressed up as a product page. And when the renders are done but the engineering isn’t, founders sometimes launch anyway. The marketing window is open, a competitor just announced something similar, momentum feels like it’s evaporating.</p><p><strong>The campaign that raises money on a story that isn’t finished yet is borrowing against a deadline it hasn’t earned.</strong></p><p>Contrast that with the modern electric hookah and mobile dental clinic projects that went through full ergonomic and manufacturing validation <em>before</em> going anywhere near a crowdfunding page. Slower to launch. Far less likely to implode after.</p><p>A well-known line from Dieter Rams has aged into cliché at this point, but it’s aged into cliché because it’s still true: good design is as little design as possible, which, translated for a founder staring at a launch day countdown, means don’t ship a promise your engineering hasn’t caught up to yet.</p><p>So here’s the actual, unglamorous truth underneath all five of these: crowdfunding was never the hard part. It was always the easiest, loudest, most public 30 days of the entire journey.</p><p>The quiet 300 days after, the ones with no confetti, no press coverage, no backer comments, are where hardware companies are actually built or quietly buried.</p><p>Which one has your campaign actually prepared for?</p><p><em>Analogy Design is a Bangalore-based industrial design studio that has taken 250+ hardware products from sketch to shelf, with 23 global design awards and clients including Panasonic, Unilever, and Marvel. More at </em><a href="https://www.analogydesign.co/"><em>analogydesign.co</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=91ec90a58271" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Nobody Stole His Invention. He Handed It Away, One Demo at a Time.]]></title>
            <link>https://blog.venturemagazine.net/nobody-stole-his-invention-he-handed-it-away-one-demo-at-a-time-a685933c565f?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/a685933c565f</guid>
            <category><![CDATA[patent-law]]></category>
            <category><![CDATA[inventions]]></category>
            <category><![CDATA[hardware-startup]]></category>
            <category><![CDATA[patents]]></category>
            <category><![CDATA[industrial-design]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Sun, 05 Jul 2026 14:22:47 GMT</pubDate>
            <atom:updated>2026-07-05T14:22:47.021Z</atom:updated>
            <content:encoded><![CDATA[<h3>The patent office doesn’t care who invented something first. It cares who kept quiet the longest.</h3><p>He had a working prototype, a LinkedIn video with forty thousand views, and a pitch deck that explained, slide by slide, exactly how his product worked.</p><p>He thought he was building momentum.</p><p>He was building prior art against himself.</p><p>Three months later, a patent attorney told him the bad news in plain language: the invention was no longer his to protect. Not because a competitor copied it. Not because someone stole his files. Because he had shown it to the world before he filed for it, and in patent law, that single ordering mistake is almost impossible to undo.</p><p>This isn’t a rare, freak occurrence. It’s one of the most common ways hardware founders lose ownership of their own ideas, and almost none of them see it coming until it’s too late.</p><figure><img alt="Founder Pitching Innovation Before Securing Patent Rights" src="https://cdn-images-1.medium.com/max/1024/1*3vFVFGaoWfPp5_bBVac5-w.jpeg" /><figcaption>File patent first. Share later. The order matters more than most founders realize.</figcaption></figure><h3>The rule nobody explains to first-time founders</h3><p>Most people assume patents work like a finish line. Whoever invents something first gets to claim it, eventually, once the paperwork catches up.</p><p>That’s not how it works in the United States, and it’s definitely not how it works almost everywhere else.</p><p>The U.S. runs on a first-to-file system. Filing date beats invention date, almost every time. And under U.S. patent law, once you publicly disclose your invention, you get a one-year grace period to file before that disclosure legally counts against you as prior art.</p><p>A year sounds generous. It isn’t, once you understand what “public disclosure” actually covers.</p><p>A demo video. A pitch deck sent without an NDA. A booth at a trade show. A working prototype shown to press. A Kickstarter page. All of it counts.</p><p>And outside the U.S.? In Europe, China, India, and most of the rest of the world, there is no grace period at all. The clock doesn’t start ticking. It simply stops. The moment your invention is public, your patent rights in those countries are gone, permanently, with no path back.</p><p>That detail alone has ended international patent strategies for products that hadn’t even launched yet.</p><figure><img alt="Early Product Showcase Can Cost Valuable Patent Protection" src="https://cdn-images-1.medium.com/max/1024/1*AndMSf9aihERaMkk8pkhmQ.jpeg" /><figcaption>Your invention isn’t protected because it’s brilliant. It’s protected because you filed.</figcaption></figure><h3>The part that should make every founder uncomfortable.</h3><p>Here’s what nobody tells you when you’re excited about your product and eager to show it off: the people you’re trying to impress, investors, journalists, trade show crowds, can become the very reason your patent application later gets rejected.</p><p>Patent examiners search for prior art. They are specifically trained to find evidence that an invention wasn’t novel at the time of filing.</p><p>Sometimes the most damaging piece of prior art an examiner finds isn’t a competitor’s product. It’s the founder’s own demo video, dated months before the filing, sitting in plain sight on the internet.</p><p>You don’t need a thief to lose your invention. You only need a publish button and bad sequencing.</p><figure><img alt="Patent Protection Lost Through Early Public Disclosure" src="https://cdn-images-1.medium.com/max/1024/1*WZY_zcpFcVM5A_SHQvcwLg.jpeg" /><figcaption>The biggest threat to your patent might be your own product launch.</figcaption></figure><h3>What actually protects an idea?</h3><p>So what’s the fix? Not silence. Founders still need to pitch, demo, and raise money. Hiding the product in a basement until it’s perfect isn’t a real strategy, it’s a way to run out of runway before anyone sees what you built.</p><p>The fix is sequencing, and it’s almost embarrassingly simple once someone explains it.</p><p>File before you talk. Not instead of talking. Before.</p><p>That doesn’t mean a fully drafted, examiner-ready patent. It means a provisional patent application, which locks in a priority date, the single most valuable date in the entire process, for a fraction of the cost and time of a full filing.</p><p>A provisional application buys twelve months. Twelve months to refine the product, raise the round, and decide whether the invention is even worth the cost of a full patent, all while the priority date is already secured.</p><p>For products built and shipped through Analogy Design, this sequencing decision shows up again and again, because it’s the difference between owning an idea and merely having had one.</p><p>When the Freedom Face Shield, a personalized PPE design, was developed at the height of COVID-19, dozens of teams worldwide were racing to file similar PPE patents at the same time. The team filed during the crisis, not after it, specifically to win first-mover advantage while it still mattered.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*kefR6hBEJG4xdFm43Z9jtw.jpeg" /><figcaption>An automated tea making machine desgined by the team at Analogy</figcaption></figure><p>With <a href="https://www.analogydesign.co/work/dostea">Dostea</a>, the world’s first automated chai-making machine, the patent application and provisional filings were handled before the product reached the stage where public exposure was unavoidable. The product is still patent-pending today, but it has had enforceable IP protection since the day that provisional was filed, not since the day the full patent might eventually be granted.</p><p>And with <a href="https://www.analogydesign.co/work/idiya">iDiya</a>, a meditation device that went on to win a granted patent from the USPTO, the process started with an unglamorous, unsexy step nobody likes to budget time for: a prior art search, conducted before the application was drafted, to map out exactly what already existed and where the real novelty was.</p><p>None of these stories involve a dramatic theft. They involve a founder, or a team advising one, simply respecting the order of operations.</p><h3>The math founders get wrong.</h3><p>Here’s the number that should genuinely bother you. Filing a provisional patent application typically costs a small fraction of what a full utility patent costs later, and it buys an entire year of protected runway.</p><p>Founders who skip it usually aren’t saving meaningful money. They’re gambling an irreplaceable priority date against a few thousand dollars and a few weeks of paperwork.</p><p>That is not a rational trade. It just feels like one in the moment, because the bill for a provisional filing arrives now, and the cost of skipping it arrives later, quietly, as a rejection letter or a competitor’s name on a patent that should have had yours on it.</p><p><strong>An idea you can’t legally call your own isn’t an asset. It’s a liability wearing the costume of one.</strong></p><figure><img alt="Product Idea Shared Publicly Prior Patent Application" src="https://cdn-images-1.medium.com/max/1024/1*Y0DJZddrc6sPBt1n4aNEQw.jpeg" /><figcaption>Before you impress the world, make sure you’ve protected your idea.</figcaption></figure><h3>Where does this actually bite people?</h3><p>The moment is rarely a single dramatic mistake. It’s almost always a string of small, well-intentioned ones.</p><p>A founder demos at a regional pitch competition to build buzz before a seed round. A team posts a product teaser on LinkedIn because the marketing calendar says so. A Kickstarter goes live because the runway is tight and pre-orders feel safer than equity.</p><p>Every one of those moves can be the right business decision. The mistake isn’t doing them. The mistake is doing them before anyone has asked a simple, unglamorous question: has this been filed yet, even provisionally?</p><p><strong>Most founders don’t lose their invention to a competitor. They lose it to their own calendar.</strong></p><h3>A reframe worth sitting with.</h3><p>The instinct in hardware is to build first and protect later, because building feels like progress and paperwork feels like friction.</p><p>But protection isn’t the opposite of momentum. It’s what makes momentum survive contact with the real world, with investors who ask hard diligence questions, with manufacturers who want exclusivity guarantees, with acquirers who will not write a check for IP they can’t verify you actually own.</p><p>So here’s the genuinely uncomfortable question worth sitting with, the one most founders avoid asking until a lawyer asks it for them: of everything you’ve already shown an investor, a journalist, or a crowdfunding audience, how much of it is already, legally, prior art against your own future patent? And if the answer is “I’m not sure,” what does that say about how this gets fixed before the next demo, not after it?</p><p>If you’ve ever found out the hard way, in a rejection letter, an office action, or a very awkward call with a patent attorney, I’d genuinely like to hear how it played out in the comments. These stories almost never make it into pitch decks, which is exactly why they keep repeating.</p><p><em>A version of this piece draws on patenting fundamentals first laid out in </em><a href="https://www.analogydesign.co/"><em>Analogy Design</em></a><em>’s longer breakdown, </em><a href="https://www.analogydesign.co/blog/a-comprehensive-guide-to-patenting-your-product-idea-and-design"><em>A Comprehensive Guide to Patenting Your Product Idea and Design</em></a><em>, for founders who want the fuller walkthrough of patent types, timing, and the U.S. and India filing process.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=a685933c565f" width="1" height="1" alt=""><hr><p><a href="https://blog.venturemagazine.net/nobody-stole-his-invention-he-handed-it-away-one-demo-at-a-time-a685933c565f">Nobody Stole His Invention. He Handed It Away, One Demo at a Time.</a> was originally published in <a href="https://blog.venturemagazine.net/">Venture</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[The Prototype That Got a Standing Ovation and Zero Dollars]]></title>
            <link>https://blog.venturemagazine.net/the-prototype-that-got-a-standing-ovation-and-zero-dollars-4854d3e9367c?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/4854d3e9367c</guid>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[prototyping]]></category>
            <category><![CDATA[hardware-development]]></category>
            <category><![CDATA[hardware-startup]]></category>
            <category><![CDATA[industrial-design]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Sun, 05 Jul 2026 14:22:34 GMT</pubDate>
            <atom:updated>2026-07-05T14:22:34.045Z</atom:updated>
            <content:encoded><![CDATA[<h3>Why investors keep saying “come back with more traction” to founders who built something genuinely impressive.</h3><h3>The room went quiet the right way.</h3><p>The founder set the device on the table. It lit up. It worked exactly like the demo video that had already racked up forty thousand views on LinkedIn.</p><p>Two investors leaned in. One actually said “wow.”</p><p>Then came the question nobody had rehearsed an answer for.</p><p>“This is great. Who’s manufacturing it at scale, and what does it cost to make one of these once you’re past unit one?”</p><p>Silence. A different kind of silence than the first one.</p><p>Three weeks later, the same founder got the line that ends more hardware raises than any bad idea ever has: <em>come back when you have more traction.</em></p><p>Here’s the part that should bother you. The product wasn’t the problem. It never is.</p><figure><img alt="Founder Presenting Product Prototype Without Manufacturing Plan" src="https://cdn-images-1.medium.com/max/1024/1*OX9JfZKObFob7b8OdKvFXA.jpeg" /><figcaption>Investors don’t fund prototypes. They fund businesses that can scale.</figcaption></figure><h3>A prototype is not a pitch.</h3><p>Most first-time hardware founders treat “investor-ready” as a build quality question. Smooth surfaces. Working buttons. No visible glue.</p><p>Investors who actually write hardware checks are not evaluating your craftsmanship. They’re running a different test entirely, and most founders never see it happen.</p><p>Research from <a href="https://www.cbinsights.com/research/startup-failure-reasons-top/">CB Insights</a> on startup failure points to a pattern that shows up across hundreds of post-mortems: companies don’t usually die from a bad product. They die from cash burn, supply chain breakage, and product-market fit problems that only surface after money has already been spent building at scale.</p><p>A hardware investor has watched that exact movie before, possibly in their own portfolio. So before they say yes to your product, they’re quietly checking whether you’ve already accounted for the five ways it could still fail after they fund it.</p><p>That checklist is invisible. It’s also the entire reason a beautiful prototype can walk into a room and walk out with nothing.</p><p>Here are four specific gaps that keep showing up, four reasons a demo that gets a “wow” doesn’t get a wire transfer.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*OqOyKb8z5duaKACOHWF3Mw.jpeg" /><figcaption>Manufacturing answers win more investor meetings than flashy demos.</figcaption></figure><h3>1. It’s been tested by you, not by a stranger who could say no.</h3><p>Founders fall in love with their own prototype faster than anyone else ever will. That’s not a character flaw. It’s just proximity.</p><p>The problem is that “I tested it and it works” and “a stranger with no loyalty to me tried it and chose to keep using it” are two completely different claims, and investors can tell which one you’re making within about ninety seconds.</p><p>Real validation looks unglamorous from the outside. Thirty unscripted conversations with the actual buyer. A landing page converting cold traffic at a real percentage, not a projected one. A pilot customer who paid, used the thing for thirty straight days, and asked for a second one.</p><p>None of that is exciting to build. All of it is the difference between a demo and evidence.</p><p><strong>A working device with zero strangers behind it is a science project with good lighting.</strong></p><h3>2. The slide deck has a margin, the spreadsheet doesn’t.</h3><p>Here’s the detail most pitch decks bury, and it’s the one worth sitting with for a second.</p><p>A device that costs forty dollars to build and sells for fifty isn’t a hardware business. It’s a very expensive hobby with a Stripe account attached.</p><p>Hardware unit economics get cruel the moment you leave the prototype stage. Component costs are higher at low volume. Logistics for physical goods cost more and fluctuate harder than logistics for anything digital. Returns and warranty claims eat margin in ways no spreadsheet built before the first shipment ever predicts correctly.</p><p>The founders who get funded have already had the uncomfortable supplier call. They know their real bill of materials cost, not an estimate pulled from a generic search. They can tell you what the margin looks like at unit one and what it looks like at unit ten thousand, and why the gap between those two numbers closes the way it does.</p><p>If your financial model was built on a desktop instead of a phone call with a factory, an experienced investor will find the seam in under five minutes.</p><h3>3. There’s no name attached to “we’ll figure out manufacturing later”.</h3><p>This is the gap that separates a founder who has shipped hardware before from one who hasn’t, and it shows up almost immediately in conversation.</p><p>“We’re talking to a few factories” is not a manufacturing strategy. It’s a sentence designed to sound like one.</p><p>Investors who’ve backed physical products are listening for specifics. A named contract manufacturer, or a shortlist of three with real conversations already underway. A backup source for every single-point-of-failure component. A tooling cost that came from an actual quote, with a timeline that includes the iteration cycles tooling almost always demands.</p><p>The deeper concern beneath this question is what investors quietly call concentration risk: one supplier, one geography, one disruption away from a halted production line. A founder who can name that risk and show the mitigation plan signals something a beautiful render never can.</p><p><a href="https://en.wikipedia.org/wiki/Design_for_manufacturability">Design for manufacturability</a> as a discipline exists precisely because the gap between “it works on my desk” and “a factory can build ten thousand of these reliably” is where most hardware timelines and budgets quietly come apart.</p><figure><img alt="Industrial Design Team Discussing Prototype Development" src="https://cdn-images-1.medium.com/max/1024/1*YBOjI_6OfpDpe3cS40jahg.png" /><figcaption>Behind every fundable hardware product is a team that knows how to take it to market</figcaption></figure><h3>4. The team can build it, but nobody on it has shipped it.</h3><p>The fourth gap is the one founders are least likely to see in themselves, because it’s not about the product at all.</p><p>A founding team with brilliant engineering and zero manufacturing or commercial experience reads to an investor as a single-point-of-failure team, no matter how good the prototype on the table looks.</p><p>Hardware is unforgiving in a specific way software isn’t. A product can fail at the design stage, the tooling stage, the quality control stage, or the launch stage, and each of those failure modes needs a different kind of scar tissue to navigate well. One brilliant generalist rarely covers all four.</p><p>As VT Rao, founder of the Bangalore-based design studio Analogy, puts it:</p><blockquote>“<strong>Investors fund the team that’s already failed at this once, not the team that’s about to.”</strong></blockquote><p>That’s not a knock on first-time founders. It’s a nudge toward closing the gap before the meeting instead of during it, by bringing in the manufacturing or commercial experience the room is already silently checking for.</p><h3>What “investor-ready” actually means</h3><p>None of these four gaps are about whether your prototype looks good. All four are about whether the story behind the prototype holds up to a stranger asking hard, specific, slightly rude questions.</p><p>A founder who has shipped exactly one hardware product, Himanshu, went from a napkin sketch for a pair of smart glasses to a CES floor in under eight months, and was acquired by Kaynes Technology shortly after. The product mattered. So did the fact that, by the time investors saw it, every one of these four questions already had an answer attached.</p><p>That’s the actual definition of investor-ready. Not polish. Preparedness.</p><p>So here’s the slightly uncomfortable question worth sitting with if you’re building hardware right now: if an investor stopped your demo mid-sentence and asked who’s manufacturing this at scale, would you have a name, or would you have a sentence that sounds like one?</p><p>I’d genuinely like to know what’s tripped you up first when you’ve pitched. Drop it below. Patterns like this are more useful in the comments than in any guide.</p><p><em>Analogy Design is a Bangalore-based industrial design studio that has helped 89 hardware founders get from prototype to fundable, manufacturable product, including the AI glasses that went from sketch to acquisition in eight months. For the deeper breakdown of what investors check before writing a check, the studio has published two companion guides: </em><a href="https://www.analogydesign.co/blog/what-investors-want-from-hardware-startup-funding"><em>what investors want to see before funding hardware</em></a><em> and </em><a href="https://www.analogydesign.co/blog/how-to-get-your-hardware-startup-funded"><em>the six signals investors evaluate in every pitch</em></a><em>. More at </em><a href="https://www.analogydesign.co/"><em>analogydesign.co</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=4854d3e9367c" width="1" height="1" alt=""><hr><p><a href="https://blog.venturemagazine.net/the-prototype-that-got-a-standing-ovation-and-zero-dollars-4854d3e9367c">The Prototype That Got a Standing Ovation and Zero Dollars</a> was originally published in <a href="https://blog.venturemagazine.net/">Venture</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[The First File We Open In A DFM Audit]]></title>
            <link>https://analogydesign.medium.com/the-first-file-we-open-in-a-dfm-audit-tells-us-almost-everything-e85b9f374335?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/e85b9f374335</guid>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[manufacturing]]></category>
            <category><![CDATA[dfm]]></category>
            <category><![CDATA[design-for-manufacturing]]></category>
            <category><![CDATA[hardware-manufacturing]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Fri, 03 Jul 2026 01:18:53 GMT</pubDate>
            <atom:updated>2026-07-03T01:19:55.499Z</atom:updated>
            <content:encoded><![CDATA[<h3>We’ve reviewed 250+ hardware products for manufacturability. What we find in the first twenty minutes has almost nothing to do with your design’s aesthetics.</h3><p>The files came in on a Tuesday afternoon.</p><p>Forty-seven CAD parts, a BOM running to sixty-three line items, and a cover note from the founder that said: “We’ve been through two design agencies already. We’re confident this is ready.”</p><p>The team opened the assembly file. Within eighteen minutes, the lead engineer had flagged three issues that would have collectively added four to six months to the production timeline if left untouched. The founder had no idea any of them existed.</p><p>This is what a Design-for-Manufacturing audit actually is.</p><p>It’s like a forensic investigation into decisions that were made quietly, early, and often without anyone in the room who had ever stood on a factory floor.</p><figure><img alt="Industrial Design Team Performing DFM Review" src="https://cdn-images-1.medium.com/max/1024/1*PodC6X2czp7W5gPCqwgR3w.jpeg" /><figcaption>Beautiful CAD models don’t guarantee manufacturable products</figcaption></figure><h3>What most founders think a DFM audit is.</h3><p>A checklist. A sign-off. A box to tick before you hand files to your contract manufacturer and wait for samples.</p><p>And to be fair, there is a checklist. Analogy’s <a href="https://www.analogydesign.co/blog/dfm-checklist">DFM checklist</a> runs twelve categories deep, covering material grades, GD&amp;T application, tolerance stack-up, tooling complexity, and sustainability labeling. It’s rigorous. It’s comprehensive. It’s also not the main event.</p><p>The checklist tells you <em>what</em> to measure. The audit tells you <em>why</em> a smart, experienced designer made a decision that will quietly destroy their timeline.</p><p>Those are completely different problems.</p><h3>The first file we open.</h3><p>Wall thickness.</p><p>Not because it’s the most catastrophic thing to get wrong, but because it is the fastest tell. A product with inconsistent wall thickness was almost certainly designed to look good in CAD, not to come out of a mold cleanly.</p><p>Uniform wall thickness matters because plastic cools at different rates across different thicknesses. Sink marks, warping, and internal stress, all of it traces back to a designer who was optimizing for the render, not the reality. The <a href="https://www.analogydesign.co/blog/dfm">full DFM guide</a> covers this in detail, but the short version is: the factory does not care how your product looks in Keyshot.</p><p>We look at wall thickness first because it tells us something beyond the geometry. It tells us whether anyone on the design team had ever spoken to a mold maker before submitting these files.</p><p>Usually, they hadn’t.</p><h3>The tolerance problem nobody talks about.</h3><p>The second thing we examine is the tolerance specification. And this is where audits get genuinely interesting.</p><p>Most hardware founders understand tolerances in the abstract: tighter is better, looser is cheaper. What almost nobody understands until they’ve been burned by it is <strong>tolerance stack-up</strong>.</p><p>Stack-up is what happens when you have an assembly with twelve components, each carrying its own tolerance band, and you add all those bands together. Individually, every part is within spec. Collectively, the product doesn’t close properly, or the button misaligns by 0.3mm, or the hinge binds under thermal expansion.</p><p>Geoffrey Boothroyd and Peter Dewhurst, the researchers who formalized DFMA methodology at the University of Rhode Island in the early 1980s, identified part-count reduction as one of the single most powerful levers for improving manufacturability. Fewer parts mean fewer tolerance interactions, fewer assembly steps, fewer failure points. Their framework earned them the National Medal of Technology in 1991. The principle hasn’t changed.</p><p>When a stack-up analysis reveals a clearance of 0.05mm between two mating surfaces, we’re not looking at a tolerance problem. We’re looking at an assembly headed for a 30 to 40 percent defect rate at volume, assuming the factory agrees to run it.</p><p><strong>Most findings that sound like “manufacturing issues” are actually design decisions that were finalized before a single manufacturer was consulted.</strong></p><h3>Draft angles. Every audit. Every time.</h3><p>If there is one finding that appears more consistently than any other, across product categories, price points, and founding team experience levels, it is missing or insufficient draft angles.</p><p>A draft angle is the slight taper applied to the vertical walls of a molded part so it releases cleanly from the tool. Typically one to two degrees for most plastics. Sounds trivial. The cost of ignoring it is not.</p><p>A part without draft either requires a more complex mold with side-actions and lifters, or it damages tooling on every ejection cycle, shortening mold life and introducing flash and surface defects at scale. A mold that should last 500,000 cycles might give you 80,000 before it needs refacing.</p><p>The <a href="https://www.analogydesign.co/blog/dfm-mistakes">list of fifty DFM mistakes</a> compiled from 250+ products includes this one near the top, consistently. Not because designers don’t know what draft angles are. Because CAD software renders a zero-draft wall exactly the same as a two-degree draft wall. You cannot see the problem. You have to check for it deliberately.</p><p>This is why an audit is not a visual inspection.</p><h3>The quote that changed how we explain this.</h3><p>VT Rao, founder of Analogy Design, put it plainly in the studio’s foundational DFM guide:</p><blockquote>The goal is crafting designs that are “not only beautiful, but also buildable.”</blockquote><p>That phrase does something useful. It refuses to frame aesthetics and manufacturability as opposites. A product can be genuinely ambitious in form, premium in surface finish, or unusual in mechanism and still pass a DFM audit cleanly, because all those things can be designed with manufacturing in mind from the start.</p><p>The audit is not here to make your product boring.<strong> It’s here to make sure your product lives.</strong></p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*kefR6hBEJG4xdFm43Z9jtw.jpeg" /></figure><h3>The Dostea moment</h3><p>When Analogy was designing <a href="https://www.analogydesign.co/work/dostea">Dostea</a>, the world’s first automated chai machine, eighteen months of development preceded the final product. It was not eighteen months of aesthetics. It was eighteen months of understanding how a machine managing water, heat, precise liquid volumes, and multiple material interfaces could be designed so that a factory could produce it at cost.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*UzF_5mHztIP35lAom-HQZA.png" /></figure><p>The <a href="https://www.analogydesign.co/work/ergonomic-backpack">Eume backpack</a> ran a similar gauntlet. A wearable product with integrated massage electronics, ergonomic load distribution, and textile interfaces. Designed so that assembly could scale without the kind of manual labor intensity that destroys unit economics. The brand went on to on to get featured on Shark Tank.</p><p>What those outcomes shared was not exceptional CAD work. It was that DFM thinking was present from week one, not introduced as a remediation step after the first factory samples came back wrong.</p><p>The <a href="https://www.analogydesign.co/blog/dfm-examples">DFM examples and case studies</a> from these projects make the before-and-after clearer than any checklist can.</p><h3>The file we’re actually most afraid to open.</h3><p>The BOM.</p><p>The Bill of Materials is where product ambition meets supply chain reality. It is the most consistently under-examined document in any pre-production package.</p><p>Three things flag immediately. First: non-standard or hard-to-source components that a founder specified because a supplier quoted them cheaply at low volume. The price doubles or the lead time triples at production volume, and the founder discovers this after tooling is committed. Second: fastener variety. A product that uses eight different screw types is a product that will have chronic assembly errors when line workers confuse M3s for M4s at 2am on a long run. Third: hidden dependencies, where a single component from a single supplier becomes a critical-path item with no qualified backup.</p><p>The <a href="https://www.analogydesign.co/blog/dfm">complete DFM guide</a> covers BOM optimization as a checklist item. In practice it reads less like a checklist and more like archaeology. You’re excavating sourcing decisions made in the first weeks of design, when cost-per-unit at volume felt like someone else’s problem.</p><p>It usually becomes very much your problem by the time samples are due.</p><p>If you’re still in the idea-to-manufacturer stage, <a href="https://www.analogydesign.co/blog/a-guide-on-how-to-manufacture-your-product-idea-instantly">this guide to manufacturing your product idea</a> is a useful primer on the decisions that shape what lands on an auditor’s desk.</p><h3>What we never flag as a DFM issue.</h3><p>A design we think is ugly.</p><p>This matters to say explicitly, because DFM audits have a reputation in founder circles as the moment when engineers bureaucratically sand down everything that made a product interesting. That is not what this is.</p><p>The <a href="https://www.analogydesign.co/blog/dfm-tools-software-and-techniques">DFM tools and simulation software</a> the audit draws on are diagnostic, not prescriptive. The <a href="https://www.analogydesign.co/blog/dfm-glossary">DFM glossary</a> runs to over 100 terms because this discipline has genuine depth, but every single item in it is aimed at the same underlying question: can this be built, by real people, at the price this product needs to sell for?</p><p>What we flag is the geometry that cannot be made at the cost the founder has modeled. The tolerance that no supplier in the target manufacturing region can hold reliably. The mechanism that requires three operators where the unit economics assume one.</p><p>None of that is about aesthetics. All of it is about survival.</p><h3>The question founders never ask but should.</h3><p>At the end of every audit, we share a prioritized list of findings: critical (redesign required before tooling), significant (will affect cost or yield), advisory (worth addressing before volume ramp).</p><p>The founders who take this well and use the audit to accelerate rather than stall, are almost always the ones who ask a specific question.</p><p>Not “how long will fixes take?” Not “which factory can work around this?”</p><p>They ask: <em>“Which of these could we have caught in week two?”</em></p><p>The answer is usually: most of them.</p><p>A DFM audit run at the right moment before tooling is committed and before the cost of change has compounded is not a gatekeeping exercise. It is a map of the decisions that will determine whether your product exists at price, at quality, and at the timeline you’ve promised someone.</p><p>The audit reveals the product beneath the prototype. And almost always, that product is fixable.</p><p>The question is only whether you gave yourself enough runway to fix it.</p><p><em>Analogy Design is an industrial design studio based in Bangalore with over 250 hardware products shipped and 23 global design awards, including Red Dot and iF. Their clients have raised more than $65M. More at </em><a href="https://www.analogydesign.co/"><em>analogydesign.co</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=e85b9f374335" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Vendor Quote Was $9 Cheaper Per Unit]]></title>
            <link>https://analogydesign.medium.com/vendor-quote-was-9-cheaper-per-unit-9290c1e14165?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/9290c1e14165</guid>
            <category><![CDATA[manufacturing]]></category>
            <category><![CDATA[hardware-development]]></category>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[industrial-design]]></category>
            <category><![CDATA[hardware]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Fri, 03 Jul 2026 00:52:40 GMT</pubDate>
            <atom:updated>2026-07-03T00:58:18.171Z</atom:updated>
            <content:encoded><![CDATA[<h3>Nobody warns founders that the most expensive line item in a manufacturing RFP is usually the one with the smallest number next to it.</h3><p>There’s a specific kind of silence that happens on a factory floor.</p><p>It’s not the silence of a machine being off. It’s the silence of forty workers standing around a mold that just spat out its three-hundredth defective part in a row, and nobody in the room being senior enough to say “stop.”</p><p>We’ve sat in that silence more than once.</p><p>The product was neither badly designed, nor the founder was careless. But because somewhere in the eight weeks before that moment, someone on the team looked at two manufacturing quotes side by side and picked the one that was nine dollars cheaper per unit.</p><p>Nine dollars. On a 10,000-unit run, that’s $90,000 saved. On paper.</p><figure><img alt="Coolest Cooler Became Kickstarter’s Biggest Warning Story" src="https://cdn-images-1.medium.com/max/1024/1*yL19PEsvuDAzkiC8YMzSaA.png" /><figcaption>Coolest Cooler Became <a href="https://www.kickstarter.com/projects/ryangrepper/coolest-cooler-21st-century-cooler-thats-actually">Kickstarter’s Biggest Warning Story</a></figcaption></figure><h3>Coolest Cooler Disaster: A $13 Million Lesson in Manufacturing</h3><p><a href="https://www.ycombinator.com/partners">Y Combinator partners</a>, who have funded more hardware startups than almost anyone, have written for years that the single fastest way to kill a hardware company isn’t a bad product idea, it’s underestimating how unforgiving the manufacturing step is once real money is committed. Quirky, once one of the most hyped hardware incubators in the world, burned through a significant share of its runway on manufacturing and inventory commitments it couldn’t sell through fast enough, and folded in 2015.</p><p>Coverage of the <a href="https://www.geekwire.com/2019/coolest-cooler-shuts-5-year-saga-leaving-20000-backers-without-kickstarter-reward/">Coolest Cooler’s infamous fulfillment delays</a>, well documented by outlets like <a href="https://www.forbes.com/sites/amyfeldman/2016/03/08/coolest-cooler-raised-13m-and-is-now-too-broke-to-fulfill-orders-lessons-from-a-kickstarter-fail/">Forbes</a> and <a href="https://www.theverge.com/2015/11/18/9758214/coolest-cooler-amazon-kickstater-shipping-production-delay">The Verge</a>, traces a similar root cause: production decisions made under time and cost pressure, with consequences that only showed up months later, on the factory floor, far from the spreadsheet where the decision was made.</p><p>Below we will see what nobody puts in the comparison spreadsheet.</p><h3>The quote that looks like a win.</h3><p>Every hardware founder eventually sits across from two vendor quotes that look almost identical. Same material spec. Same tolerances on paper. Same delivery promise.</p><p>One is cheaper.</p><p>It’s tempting to treat that number the way you’d treat a flight comparison. Same outcome, lower price, obvious choice. A founder we worked with treated it exactly that way, eight weeks before a retail ship date that had already been promised to a buyer.</p><p>The cheaper vendor had quoted lower because they were running an older single-cavity mold setup and absorbing the tooling cost into “free.” Free tooling sounds generous. It is, until you realize free tooling usually means a tool built to the absolute minimum spec required to survive the first few thousand cycles, not the hundred thousand cycles a real production run demands.</p><p>The team didn’t know that going in. Most don’t.</p><h3>What actually happened on the floor.</h3><p>Three weeks into the pilot run, the parts started warping.</p><p>Not catastrophically. Just enough that one in four units failed the fit-check against the enclosure. The cheaper vendor’s engineers suggested increasing cooling time per cycle to fix it, which solved the warping and quietly tripled the cycle time, which quietly tripled the per-unit labor cost that wasn’t in the original quote.</p><p>Then the mold cracked.</p><p>A new tool, on a vendor’s own admission, takes real lead time to rebuild properly. The founder didn’t have that lead time. The retail buyer didn’t care whose fault it was. The ship date didn’t move because the mold did.</p><p>This is the part of Design for Manufacturing that almost never makes it into a pitch deck: a manufacturing decision made in week one quietly decides whether week twenty goes well, badly, or not at all. It’s the same idea Geoffrey Boothroyd and Peter Dewhurst were chasing back in the early 1980s when they built the first structured framework for evaluating whether a design could actually survive contact with a factory, work that eventually earned them the National Medal of Technology. The framework hasn’t changed much. The stakes for an independent founder, with one shot at a launch window, are a great deal higher than they were for the institutions that framework was originally built for.</p><blockquote><strong><em>“Designs that are not only beautiful, but also buildable.”</em></strong><em> <br>- VT Rao, Founder, Analogy Design</em></blockquote><p>That phrase sounds like a tagline until you’ve watched a founder try to explain to a retail buyer why six pallets of product are sitting in a bonded warehouse failing inspection.</p><h3>The number nobody wants to say out loud.</h3><p>Here’s the detail most people ask about first, and the one we’re going to make you wait for, because it’s the one that actually changes how you read everything before it.</p><p>The “cheaper” vendor wasn’t cheaper.</p><p>By the time the founder had paid for the failed pilot batch, paid the original vendor a kill fee to walk away mid-tool, and rushed a second vendor to rebuild a production-grade mold on an expedited timeline, the total cost landed meaningfully above what the more expensive, properly-tooled vendor had quoted on day one.</p><p>The $90,000 “savings” wasn’t a saving. It was a deposit on a much larger bill that simply hadn’t arrived yet.</p><p>This is not a rare story. It’s a pattern.</p><h3>Why “cheaper” and “lower risk” are almost never the same word.</h3><p>A vendor quote is not just a random price. It’s <strong>a bet on a hundred decisions</strong> you can’t see yet: how worn their existing tooling is, how senior the engineer reviewing your file actually is, whether they’ve built this exact wall thickness in this exact material before, whether their quality team has the authority to stop a bad run or just the instruction to keep the line moving.</p><p>None of that shows up in a per-unit number.</p><p>It shows up in a <a href="https://www.analogydesign.co/blog/dfm-checklist">DFM review</a>, the kind of unglamorous, line-by-line audit of tolerances, draft angles, and process compatibility that founders are usually in too much of a hurry to take seriously until they’ve already been burned once. Analogy’s own <a href="https://www.analogydesign.co/blog/dfm">Design for Manufacturing guide</a> exists specifically because the gap between “this looks fine on the CAD file” and “this survives ten thousand production cycles” is where most of these disasters quietly begin.</p><p>The cheapest quote optimizes for the number you can compare today. The right quote optimizes for the disaster you can’t see yet, which is the only one that actually costs you anything.</p><h3>The question worth sitting with.</h3><p>If you’ve shipped hardware, you already know which line in your last RFP you wish you’d read more carefully.</p><p>So here’s the genuinely uncomfortable question: how much of the “we need to keep costs down” pressure on your last sourcing decision actually came from your investors, and how much of it did you put on yourself, because saying “we need a better vendor” out loud felt like admitting you’d budgeted the project wrong from the start?</p><p>That’s not a rhetorical question. We’d genuinely like to know what you decided, and what it cost you to find out you were right or wrong.</p><p>The cheapest vendor is never actually cheap. It just postpones the bill to a week when you’ll have far less leverage to negotiate it.</p><p><em>Analogy Design is a Bangalore-based hardware product design studio. More on how teams de-risk manufacturing decisions before they become expensive ones at </em><a href="https://www.analogydesign.co/"><em>analogydesign.co</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=9290c1e14165" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[The $180,000 Mistake Nobody Noticed Until the Boxes Arrived]]></title>
            <link>https://analogydesign.medium.com/the-180-000-mistake-nobody-noticed-until-the-boxes-arrived-614643e08975?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/614643e08975</guid>
            <category><![CDATA[hardware]]></category>
            <category><![CDATA[product-design]]></category>
            <category><![CDATA[cad]]></category>
            <category><![CDATA[hardware-startup]]></category>
            <category><![CDATA[product-development]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Wed, 01 Jul 2026 01:10:33 GMT</pubDate>
            <atom:updated>2026-07-01T01:10:33.733Z</atom:updated>
            <content:encoded><![CDATA[<h3>Seven decisions that feel like rounding errors on a CAD screen and turn into six-figure holes on a factory floor, and the one question that catches all of them before the tooling gets cut.</h3><figure><img alt="Rounding Errors On A CAD Screen" src="https://cdn-images-1.medium.com/max/1024/1*5jJXPaIrFKKT19xdjhWrnQ.jpeg" /></figure><p>He didn’t say anything for almost a minute.</p><p>The factory floor in Shenzhen was loud, full of presses and conveyor hum, and he just stood there holding a tooling change order with a number on it that didn’t match the number in his spreadsheet.</p><p>The problem was neither a typo, nor a rounding issue. A number that was going to come out of a budget that had already been spent twice over in his head.</p><p>This is the moment that happens to almost every hardware founder once. Quietly, usually alone, usually somewhere between the third and seventh month of a build. Nobody warns you about it because it doesn’t look like a crisis from the outside. It looks like an email with an attachment.</p><p>I’ve watched this exact moment happen to dozens of founders over a decade of building physical products in Bangalore. Same shape every time. A design that looked finished on screen. A manufacturer who quietly absorbed the first version’s problems and then stopped absorbing them. And a gap between “designed” and “designed to be made” that nobody budgeted for because nobody could see it coming.</p><p><a href="https://www.analogydesign.co/blog/dfm">Design for Manufacturing or DFM</a>, is the unglamorous discipline that closes that gap. It’s also, according to a quality-engineering principle known as the rule of ten, a way of showing that the cost of fixing an error multiplies roughly tenfold at each later stage of production it’s caught in. Catch it on a screen, it costs an afternoon. Catch it after tooling, it costs a redesign. Catch it after the container ships, it costs your runway.</p><p>Here are the seven mistakes that keep doing this, quietly, to founders who are otherwise doing everything right.</p><h3>The part that looked fine until it had to come out of a mold</h3><p>Plastic parts need draft angle, a tiny taper that lets a molded piece release from its tool without tearing.</p><p>Skip it, or specify it wrong, and the part doesn’t pop out clean. It scuffs. It cracks. Sometimes it just won’t release at all, and the mold has to be re-cut.</p><p>This single oversight is one of the most common reasons a “ready” CAD file turns into a re-tooling invoice. It rarely shows up in a 3D-printed prototype, because resin prints don’t care about mold release. It only shows up the first time the part meets steel.</p><h3>Tolerances stacked like nobody was watching the math</h3><p>A single part can be perfectly within spec and still not fit.</p><p>This happens when small, individually acceptable tolerances on five or six parts compound into one big misalignment by the time they’re assembled together. Engineers call it tolerance stack-up, and it’s one of those problems that’s invisible until an assembly line worker is staring at a hinge that won’t close.</p><p>It’s rarely caught by checking parts one at a time. It’s only caught by simulating the whole assembly, on purpose, before anything gets tooled.</p><p><strong>A tolerance that’s fine on paper and a tolerance that’s fine in a stack of six other tolerances are two completely different things.</strong></p><figure><img alt="Hardware Product MVP Prototype By Analogy" src="https://cdn-images-1.medium.com/max/1024/1*0C0o6MymVM6hJ89BaaonVw.jpeg" /><figcaption>Analogy team reviewing a hardware product protype</figcaption></figure><h3>A material chosen for the demo, not for the run</h3><p>A material that machines beautifully at five units can behave completely differently at five thousand.</p><p>Shrinkage rates, flow characteristics, and surface finish compatibility all shift with volume and process, and a material picked because it looked good on a benchtop prototype can quietly add cost, defects, or both the moment real production volume kicks in.</p><p>This is the mistake that hides longest, because the early samples genuinely look great. The first sign of trouble is usually a yield report, not a CAD review.</p><h3>The bill of materials nobody trimmed</h3><p>Every additional fastener type, every extra joining method, every slightly different screw size is one more line item a factory has to stock, train for, and slow down for.</p><p>A bill of materials with twelve fastener types instead of four doesn’t look dramatic on a spec sheet. It looks dramatic on an assembly line, where every changeover costs labor time, and labor time at scale is where margins quietly disappear.</p><p>This is rarely a single bad decision. It’s usually a dozen small “this one’s slightly better” choices that nobody ever sat down and totaled.</p><h3>Designing for the process before deciding what the process is</h3><p>A geometry that’s perfect for CNC machining can be a nightmare for injection molding, and a part designed without knowing which one it’s headed for is a part designed twice.</p><p>This sounds obvious written down. It is, somehow, one of the most common things to skip when a team is moving fast and the manufacturing partner hasn’t been chosen yet.</p><p>A friend who advises hardware founders, Sera Evcimen, has told <em>TechCrunch</em> that production costs typically run two to three times longer than founders plan for, and four to five times more expensive than expected, sometimes worse, because designs get the manufacturing process wrong on the first attempt, triggering change orders, low yields, and stacked delays.</p><p>Four to five times more expensive isn’t a rounding error. It’s the difference between a runway that gets you to Series A and one that doesn’t.</p><h3>Treating the prototype like a rehearsal instead of evidence</h3><p>A prototype that’s never actually validated against the real assembly process is a beautiful object with an unanswered question baked into it.</p><p>3D-printed prototypes flex, bend, and fail differently than injection-molded production parts. Assuming the two will behave the same way is one of the quieter ways a team convinces itself it’s further along than it is.</p><p>This is the mistake that’s almost invisible at the prototype stage, because everything <em>looks</em> done. It only becomes visible when the first production batch behaves nothing like the demo unit everyone fell in love with.</p><h3>Skipping the one conversation that catches all six of the above</h3><p>Every mistake above has the same fix, and it isn’t a checklist. It’s a conversation.</p><p>A DFM review, sitting design and manufacturing engineers in the same room before tooling gets cut, is the single highest-leverage hour in a hardware build. It’s also the easiest one to skip when a team is racing toward a deadline.</p><p>Dieter Rams, who spent over three decades shaping how Braun built physical products, put it simply: “good design is as little design as possible.” Less but better isn’t just an aesthetic preference. It’s a manufacturing strategy. Every feature, every fastener, every clever undercut is something a factory has to physically execute, over and over, at a price.</p><p><strong>Here’s the part of this that nobody wants to say out loud.</strong></p><p>None of these seven mistakes require incompetence. They require speed, and speed is exactly what every early-stage hardware team is optimizing for.</p><p>The founder on that factory floor wasn’t careless. He was fast, like everyone in his position needs to be. He just hadn’t yet learned that the fastest version of hardware development is the one where manufacturing gets a seat at the table in month one, not month seven.</p><p>We’ve sat across the table from that exact moment more times than I can count, including with the team behind a pair of AI glasses that went from a napkin sketch to a CES stage to an acquisition in under eight months, a timeline that only works when manufacturing reality gets designed in from day one, not bolted on at the end.</p><p>So here’s the question worth sitting with, whether you’re three months into a build or three weeks from launch: when was the last time your manufacturing partner saw your design before it was “finished”?</p><p>If the honest answer is “after,” you already know where the next surprise invoice is hiding.</p><p><em>Analogy Design is a Bangalore-based industrial design studio that has shipped 250+ hardware products and run the manufacturing math on most of the mistakes above, including a longer breakdown of all the ways this goes wrong at </em><a href="https://www.analogydesign.co/blog/dfm-mistakes"><em>analogydesign.co/blog/dfm-mistakes</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=614643e08975" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[We’ve Designed 250 Hardware Products. Same 10 Mistakes Keep Coming Back.]]></title>
            <link>https://analogydesign.medium.com/weve-designed-250-hardware-products-same-10-mistakes-keep-coming-back-c6c479930ddc?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/c6c479930ddc</guid>
            <category><![CDATA[hardware-design]]></category>
            <category><![CDATA[prototyping]]></category>
            <category><![CDATA[hardware-startup]]></category>
            <category><![CDATA[manufacturing]]></category>
            <category><![CDATA[rapid-prototyping]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Wed, 01 Jul 2026 01:04:57 GMT</pubDate>
            <atom:updated>2026-07-01T01:04:57.800Z</atom:updated>
            <content:encoded><![CDATA[<h3>Founders don’t repeat mistakes because they’re careless. They repeat them because the first time, it didn’t feel like a mistake. It felt like progress.</h3><p>A founder once walked into our studio in Bangalore holding a CAD render on his phone like it was a finished product.</p><p>It wasn’t. It was a picture of a product. Beautiful lighting, perfect angles, zero idea whether it could survive a drop test.</p><p>He’d already quoted a manufacturer. Already told investors a ship date. Already, in his head, moved on to the next problem.</p><p>That’s the thing about hardware. The mistakes don’t announce themselves. They dress up as momentum.</p><figure><img alt="Analogy team in a brainstorming session" src="https://cdn-images-1.medium.com/max/1024/1*YBOjI_6OfpDpe3cS40jahg.png" /><figcaption><em>Analogy team in a brainstorming session</em></figcaption></figure><p>We’ve sat across the table from 250+ of these moments. Watched founders raise real money, hit real deadlines, and ship real products to <a href="https://www.analogydesign.co/work/panasonic-miraie">Panasonic</a>, <a href="https://www.analogydesign.co/work/ergonomic-toothbrush-for-pepsodent">Unilever</a>, <a href="https://www.analogydesign.co/work/festivity-packaging-amazon">Amazon</a>, <a href="https://www.analogydesign.co/work/employee-kit-maersk">Maersk</a>, <a href="http://www.analogydesign.co/work/outdoor-gear-for-wildcraft">Wildcraft</a>. We’ve also watched, more times than we’d like, the same handful of mistakes resurface in year two after a founder swore they’d never make them again.</p><p>Here are ten of them. No theory, but pattern.</p><p><strong>1. Mistaking a render for a product.</strong></p><p>A render answers “does it look good.” It says nothing about tolerance stack-ups, assembly, or whether the plastic will warp in a Bangalore summer. Founders fall for this twice because the first render <em>did</em> get them funding. So they assume the second one will get them a factory.</p><p><strong>2. Locking the form before locking the function.</strong></p><p>The shape gets approved in a slide deck before anyone has stress-tested what’s actually inside it. Then engineering spends three months trying to fit electronics into a silhouette that was never built to hold them.</p><p><strong>3. Hiring the industrial designer after the engineering is frozen.</strong></p><p>This is the mistake that costs the most money for the least reason. Bring in design thinking after the architecture is locked, and you’ve hired a stylist, not a problem-solver. Dieter Rams put it plainly: <em>“Good design is as little design as possible.”</em> That only works if design is in the room from day one, not called in to decorate a decision that’s already made.</p><p><strong>4. Optimizing for the demo instead of the unit that ships.</strong></p><p>This is the one founders almost never admit to themselves the first time.</p><p>Here’s the detail we usually hold back: one of the fastest journeys we’ve been part of took a single sketch to a working unit on the CES floor, and from there to acquisition by Kaynes Technology, in under eight months. That speed wasn’t luck. It came from designing the <em>real</em> unit early, not a demo-only version dressed up for a stage. Founders who build a gorgeous one-off for a trade show, then try to reverse-engineer it into something a factory can build 10,000 times, are doing the hardest version of this job twice.</p><p><strong>5. Treating ergonomics as a finishing touch.</strong></p><p>Human factors research has tracked repetitive strain and discomfort tied to badly weighted products for decades. It’s not a soft science. When we worked on an ergonomic backpack designed around how a spine actually carries weight, the difference between “looks comfortable” and “is comfortable” was the entire pitch. That backpack, Eume, walked into Shark Tank and walked out at a $4.5M valuation. Comfort wasn’t the garnish. It was the product.</p><figure><img alt="Skipping DFM until the mold is already cut" src="https://cdn-images-1.medium.com/max/1024/1*OhnHn2yfWqPVjP3Nhyyl5Q.jpeg" /><figcaption>DFM is integral and skipping it costs more than you think</figcaption></figure><p><strong>6. Skipping DFM until the mold is already cut.</strong></p><p>Design for manufacture is one of those phrases that sounds like homework. Skip it, and you find out the hard way, after tooling, that a feature you loved can’t be molded without a $40,000 redesign. Founders who get burned here once usually swear off it. Founders who get burned twice usually didn’t actually understand what broke the first time, they just got a new vendor.</p><p><strong>7. Believing a flashy outcome means the hard part is over.</strong></p><p>A flame-less commercial stove, a fully automated chai machine, a mobile dental clinic that drives to the patient instead of the other way around — every one of these started as “the hard part is the idea.” It isn’t. The idea is the cheap part. As outlets like Core77 and Fast Company have covered repeatedly in their CES wrap-ups, the gap between “impressive demo” and “investable company” is almost entirely manufacturing discipline, not inspiration.</p><p><strong>8. Letting the founder be the only eye on the form factor.</strong></p><p>One person, however brilliant, has one set of biases about how a product should look and feel. We’ve watched products go through three rounds of “the founder doesn’t like it” before anyone asked whether the <em>user</em> would like it. A toothbrush we reworked for Pepsodent only got better once the question shifted from “does the founder think this feels premium” to “does a child’s hand actually grip this correctly.”</p><p><strong>9. Raising the money before doing the homework on tooling cost.</strong></p><p>Funding events feel like finish lines. They’re not. They’re the moment the real spending starts. Y Combinator’s own startup guidance has said for years that hardware founders consistently underestimate timeline and overestimate how far a single raise will stretch. Founders who treat a raise, or a strong Shark Tank number, as proof they’ve solved manufacturing are the ones who come back twelve months later solving it for the first time, again.</p><p><strong>10. Not writing any of this down.</strong></p><p>This is the quiet one. The mistake isn’t the mistake. It’s that nobody on the team documented <em>why</em> decision four went wrong, so when a new hire or a new product line hits the same fork in the road, the team makes the exact same turn. Institutional memory is the cheapest insurance a hardware company never buys.</p><p><strong>Here’s the uncomfortable part.</strong></p><p>None of these are knowledge problems. Every founder we’ve sat across from could explain DFM, ergonomics, and tooling cost back to us in a meeting. They just didn’t believe it applied to <em>their</em> product, the first time.</p><p><em>The second time, it’s not a knowledge gap anymore. It’s a habit.</em></p><p>So here’s the question worth sitting with: which one of these have you made twice, and did you actually know it was happening the second time, or did it just feel like progress again?</p><p><em>Analogy Design is a Bangalore-based industrial design studio that has shipped 250+ hardware products across ten years, which means they’ve had a front-row seat to most of the mistakes above, sometimes twice. A longer version of this pattern lives at </em><a href="https://www.analogydesign.co/blog/hardware-startup-mistakes"><em>analogydesign.co/blog/hardware-startup-mistakes</em></a><em>.</em></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=c6c479930ddc" width="1" height="1" alt="">]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[7 steps to making a prototype and supercharging your product design]]></title>
            <link>https://analogydesign.medium.com/7-steps-to-making-a-prototype-and-supercharging-your-product-design-fe3da679576e?source=rss-991a19e7be1f------2</link>
            <guid isPermaLink="false">https://medium.com/p/fe3da679576e</guid>
            <category><![CDATA[product-design]]></category>
            <category><![CDATA[prototyping]]></category>
            <category><![CDATA[testing]]></category>
            <category><![CDATA[industrial-design]]></category>
            <category><![CDATA[design]]></category>
            <dc:creator><![CDATA[Analogy]]></dc:creator>
            <pubDate>Fri, 15 Dec 2023 14:35:42 GMT</pubDate>
            <atom:updated>2023-12-15T14:35:42.180Z</atom:updated>
            <content:encoded><![CDATA[<figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*3IHLKaSfg_G2MFWxDn_j6A.png" /></figure><p>Hello and welcome to the latest edition of <strong>Beyond The Surface</strong>, the newsletter that helps you turn your ideas into reality. In this edition, we will cover how to create a working prototype in 7 steps, and what are the benefits of using a prototype for your product development.</p><h3>Prototypes and why we need them</h3><p>A prototype is a preliminary version of your product that you can use to test its functionality, design, and feasibility. Creating a prototype can help you refine your product before investing in production, marketing, and distribution. Prototyping is considered a vital and essential step in the product development process for its numerous benefits.</p><p>Prototypes allow the creators to test and validate their ideas in the real world. Prototypes can help to check the functionality, usability, feasibility, and desirability of a product before investing in mass production. Prototypes can also help to communicate the product idea to potential customers, investors, partners, or media, and solicit feedback and suggestions for improvement. Prototypes can also help to determine the best materials, components, and techniques to use for the final product. <a href="https://www.cadcrowd.com/blog/why-is-industrial-design-important-for-new-product-and-prototype-development/">Prototypes can vary in their level of fidelity and detail, depending on the purpose and stage of the product development process</a></p><p>Here are the 7 steps to create a working prototype for your product:</p><h3>1. Conduct research</h3><p>Before you start designing your prototype, you need to do some research on your target market, competitors, customer needs, and industry trends. This will help you identify the problem you are solving, the value proposition of your product, and the features and specifications you need to include. <a href="https://analogydesign.co/work/bloom-wireless-charger/">Read how we conducted extensive research to understand the users of Bloom — wireless charger, designed by Analogy for Eurotronic.</a> Research can be conducted by studying the market and market trends, analyzing user behaviour and looking at past performance of similar ideas and products. There are a multitude of research methodologies that we employ at Analogy — demographic and psychographic segmentation, user studies and surveys, <a href="https://www.designkit.org/mindsets/4.html">empathy mapping</a>, competitor research, product breakdowns, etc. These research techniques help the team at Analogy finalize the product prototype requirements.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*pkr91Bus5ae8lZlw" /></figure><h3>2. Draw a design</h3><p>It is often said that a picture is worth a thousand words. We believe this is quite true when it comes to industrial design and prototyping. The next step is to sketch out your product idea on paper or on a digital tool. You don’t need to be an expert artist, just draw the basic shape, dimensions, and components of your product. This will help you visualize how your product will look like and how it will work.</p><p>A simple hand drawn sketch describing the visuals of a product prototype from 2–3 angles can help you anticipate and solve numerous problems in prototype development, well in advance. Quite often, we begin our projects’ ideation phase by simply sketching on post it notes or A5 sheets. For projects like <a href="https://my.idiyawellness.com/coming-soon01">iDiya</a>, the sketching phase was quite extensive since the form of the product had rotational symmetry. <a href="https://analogydesign.co/work/idiya/">Read about our design and prototyping process for iDiya.</a></p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*SGEgpSPXIChU9Ap3" /></figure><h3>3. Develop a virtual model</h3><p>Once you have a rough sketch of your product, you can use a software tool to create a 3D model of your product. This will allow you to see your product from different angles, add colors and textures, and make adjustments as needed. You can also use a simulation tool to test how your product will perform under different conditions and scenarios.</p><p>3D tools like SolidWorks, Fusion 360 and Rhinoceros 3D are quite helpful for developing 3D CAD models of your product. Each of these tools have their own strengths and weaknesses and your choice of tool will depend on multiple factors — where you are in the prototype development process, amount of versatility needed in the model, who is using the virtual model and what it is being used for. Our work for Cellairis designing rugged iPhone cases involved a lot of CAD modelling, which later helped out our clients by reducing their tooling cost by 60% with a 40% increase in impact protection. <a href="https://analogydesign.co/work/cellairis-alpha-rugged-case/">Click here to see how we achieved these results for our client.</a></p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*qOHYNske-DHee91L" /></figure><h3>4. Determine whether you require assistance</h3><p>Depending on the complexity and scope of your product, you may need some help from experts or professionals to create your prototype. For example, you may need an engineer to help you with the technical aspects, a designer to help you with the aesthetics, or a manufacturer to help you with the materials and production. You can also use online platforms or services to find freelancers or collaborators who can assist you with your project.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*Qp8S9sC9xQVOq_27" /></figure><p>Using our multiple models of engagement, Analogy works with the largest and smallest companies, providing them with tailored assistance to reach their product and prototype goals. We work with recently incorporated startups headed by enthusiastic first time founders, as well as large Fortune 500 companies with global teams and multiple business units. <a href="http://www.analogydesign.co/services">Click here to explore how our service models and how we can help you achieve your prototyping goals.</a></p><h3>5. Generate a proof of concept</h3><p>A proof of concept is a simple demonstration that shows that your product idea is feasible and viable. It can be a video, a presentation, or a prototype that showcases the core functionality and value of your product. A proof of concept can help you validate your assumptions, get feedback from potential customers or stakeholders, and attract investors or partners.</p><p>Remember that a proof of concept is just that, a proof of your product’s concept. It isn’t supposed to be the final product or the fully functional prototype. Many inventors get caught up in the endless cycle of trying to perfect the Proof of Concept. What they forget is that multiple such models can be build to showcase and test various different functionalities and aspects of the products’ design.</p><p>While designing the employee onboarding kits for Maersk, we developed multiple Proofs of Concepts to validate the size, items, graphics and textures. <a href="https://analogydesign.co/work/maersk-tech-1000/">Here’s how we did it for Maersk</a>.</p><p>One model could validate the size and scale of the product, another could demonstrate the core functionality while a third could be a purely aesthetic model showcasing the paint and finish scheme of the product.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*ApS5LYxTOEsbdPm7" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*Foiu9jMIwekYfhTY" /></figure><h3>6. Create your prototype</h3><p>After you have validated your proof of concept, you can start creating your actual prototype. There are different types of prototypes that vary in their level of fidelity and detail. You can choose the type that best suits your needs and budget. Some common types are:</p><ul><li><strong>Paper prototype:</strong> A low-fidelity prototype that uses paper or cardboard to represent the physical appearance and interaction of your product. It is cheap and easy to make, but it has limited functionality and realism.</li><li><strong>Digital prototype:</strong> A medium-fidelity prototype that uses software tools to create an interactive simulation of your product. It is more realistic and functional than a paper prototype, but it may not reflect the actual look and feel of your product. Digital prototypes are used extensively to run through apps, websites and other digital products. <a href="https://analogydesign.co/work/insane-fit-ai-powered-camera-tracking-app/">Read about how we built prototypes of an AI powered camera fitness tracking app for our clients.</a></li><li><strong>Low fidelity prototypes</strong> are quick and simple versions of a product that are used to test core functionality and user flows. They are usually created early on in the design process and don’t require a lot of time or resources to produce. Low fidelity prototypes can be either hand-drawn sketches or basic digital wireframes without color or content.These low-tech designs allow UX designers to visualize each screen’s layout, test navigation, and experience user flows. <a href="https://www.usability.gov/how-to-and-tools/methods/prototyping.html">Low fidelity prototypes are useful for gathering feedback on basic structural elements</a>, such as information architecture, hierarchy, and content placement, without the potential distraction of visual design factors like colors and typefaces.</li><li><strong>High fidelity prototypes</strong> are much more detailed versions of a product that closely resemble the final user experience. They are usually created later on in the design process, once the core functionality and user journeys have been validated with low fidelity prototypes. Creating high fidelity prototypes usually requires more time and resources than low fidelity ones. High fidelity prototypes can be created using software tools that allow designers to add colors, content, images, icons, fonts, and interactivity to their wireframes. These high-tech designs allow UX designers to test visual design ideas and get buy-in from stakeholders. <a href="https://www.uxpin.com/studio/blog/high-fidelity-prototyping-low-fidelity-difference/">They are also very useful for conducting user research sessions like usability testing, providing a more true-to-life scenario than low fidelity can offer.</a></li><li><strong>Physical prototype:</strong> A high-fidelity prototype that uses materials and components that are similar or identical to those of your final product. It is the most realistic and functional type of prototype, but it is also the most expensive and time-consuming to make.</li></ul><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*qKGdtoG-z4eh1Juq" /></figure><h3>7. Repeat any steps as needed</h3><p>Creating a prototype is an iterative process that requires testing, evaluation, and improvement. You should test your prototype with real users or customers, collect feedback, measure results, and identify areas for improvement. <a href="https://www.pacific-research.com/5-advantages-of-iterative-design-and-prototyping-prl/">You should then make changes to your design or functionality based on the feedback and test again</a> until you are satisfied with your prototype. <a href="https://analogydesign.co/blog/blog-design-is-messy/">Read about how we approach iterative prototyping and design process at Analogy.</a></p><h3>What are the benefits of using a prototype?</h3><p>Creating a prototype can offer many benefits for your product development process, such as:</p><ul><li><strong>Tests your product’s functionality:</strong> A prototype can help you check whether your product works as intended and meets the needs and expectations of your customers. You can also identify any errors or flaws in your design or functionality and fix them before they become costly or irreversible.</li></ul><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*NRBl8epu6zrqT7To" /></figure><ul><li><strong>Saves money before production:</strong> A prototype can help you avoid wasting money on producing a product that may not work well or sell well. You can also use a prototype to estimate the cost of production, materials, labor, and distribution for your final product. <a href="https://analogydesign.co/work/bolt-wireless-car-charger/">Read how we used prototyping methodologies for designing a wireless car charger for Cellairis</a>.</li></ul><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*-ouP4G0hedR5z2j5" /></figure><ul><li><strong>Allows you to demonstrate your product to investors:</strong> A prototype can help you showcase your product idea to potential investors or partners who may be interested in funding or supporting your project. A prototype can also help you prove the feasibility and viability of your product and increase your credibility and confidence.</li><li><strong>Determines your product’s usefulness:</strong> A prototype can help you test whether your product solves a real problem or adds value to your customers. You can also use a prototype to measure the demand and market potential of your product and adjust your strategy accordingly.</li></ul><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*xYSaZkkLWH0Q6mvv" /></figure><ul><li><strong>Highlights the proper materials to use:</strong> A prototype can help you determine the best materials and components to use for your final product. You can also use a prototype to test the durability, quality, and safety of your product and ensure that it meets the standards and regulations of your industry.</li></ul><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*Q2YbpTz6FW1J8zG2" /></figure><ul><li><strong>Helps you coherently discuss your product:</strong> A prototype can help you communicate your product idea clearly and effectively to different audiences, such as customers, investors, partners, or media. You can also use a prototype to solicit feedback, suggestions, or opinions from others and incorporate them into your product development.</li></ul><h3>Conclusion</h3><p>Creating a working prototype is an essential step in developing a successful product. It can help you test, validate, improve, and present your product idea in a realistic and tangible way. By following the 7 steps outlined in this newsletter, you can create a working prototype that will bring you closer to your product launch. We hope you found this newsletter helpful and informative. If you have a problem you’d like to solve and are wondering how prototyping can help you, feel free to contact us at <a href="/service/mailto:business@analogydesign.co">business@analogydesign.co</a> and schedule a free discovery call. Thank you for reading and stay tuned for the next issue of <strong>Beyond The Surface</strong>!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/916/0*l7vM4XwOJS4AHQd1" /></figure><p><a href="https://analogydesign.co/">Analogy</a> Is a Bangalore based Product Design studio that has been working with clients small and large to create harmonized and relevant user experiences by combining physical and digital products and services for more than a decade. We are an <a href="https://analogydesign.co/about/">award winning global studio</a> that has resources in Singapore, US, Europe and APAC. We specialize in <a href="https://analogydesign.co/industrial-design/">Industrial design</a>, <a href="https://analogydesign.co/interaction-design/">Interaction design</a>, HMI and product branding to create one stop solutions for our clients. Some of our previous and existing clients include <a href="https://www.linkedin.com/company/google/">Google</a>, <a href="https://www.linkedin.com/company/panasonic/">Panasonic</a>, <a href="https://www.linkedin.com/company/marvel-entertainment/">Marvel Entertainment</a>, <a href="https://www.linkedin.com/company/maersk-group/">A.P. Moller — Maersk</a>, <a href="https://www.linkedin.com/company/bajajelectricals/">Bajaj Electricals Ltd</a>, <a href="https://www.linkedin.com/company/mondelezinternational/">Mondelēz International</a>, <a href="https://www.linkedin.com/company/boat-lifestyle/">boAt Lifestyle</a>, <a href="https://www.linkedin.com/company/borosillimited/">Borosil Limited</a>. We specialize in creating fresh new solutions for Consumer Electronics, Automotive, Lifestyle &amp; Tech Accessories, Audio &amp; Video products, Sporting Goods, Footwear, Mixed Reality Hardware and Scientific Products.</p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=fe3da679576e" width="1" height="1" alt="">]]></content:encoded>
        </item>
    </channel>
</rss>