<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0" xmlns:cc="http://cyber.law.harvard.edu/rss/creativeCommonsRssModule.html">
    <channel>
        <title><![CDATA[Stories by Juha Vehnia on Medium]]></title>
        <description><![CDATA[Stories by Juha Vehnia on Medium]]></description>
        <link>https://medium.com/@juha.vehnia?source=rss-810e08f0c2b6------2</link>
        <image>
            <url>https://cdn-images-1.medium.com/fit/c/150/150/0*KEe4TdojFHq5OjRZ.</url>
            <title>Stories by Juha Vehnia on Medium</title>
            <link>https://medium.com/@juha.vehnia?source=rss-810e08f0c2b6------2</link>
        </image>
        <generator>Medium</generator>
        <lastBuildDate>Sat, 21 Nov 2026 14:27:22 GMT</lastBuildDate>
        <atom:link href="https://medium.com/@juha.vehnia/feed" rel="self" type="application/rss+xml"/>
        <webMaster><![CDATA[yourfriends@medium.com]]></webMaster>
        <atom:link href="http://medium.superfeedr.com/" rel="hub"/>
        <item>
            <title><![CDATA[Porsche Cayman 981 IPD Plenum and GT3 throttle body installation]]></title>
            <link>https://medium.com/@juha.vehnia/cayman-981-ipd-plenum-and-gt3-throttle-body-installation-ad4cd601c68f?source=rss-810e08f0c2b6------2</link>
            <guid isPermaLink="false">https://medium.com/p/ad4cd601c68f</guid>
            <category><![CDATA[ipd-plenum]]></category>
            <category><![CDATA[diy]]></category>
            <category><![CDATA[porsche]]></category>
            <dc:creator><![CDATA[Juha Vehnia]]></dc:creator>
            <pubDate>Sun, 01 Apr 2018 20:03:14 GMT</pubDate>
            <atom:updated>2019-09-20T15:57:34.988Z</atom:updated>
            <content:encoded><![CDATA[<figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*YDXRq505gOaOtG6Wtcs3IQ.jpeg" /></figure><h3>Preparation</h3><p>You will need the following:</p><ul><li>Torx driver set</li><li>Standard socket set (metric of course)</li><li>Thread lock</li><li>Putty knife or some other flat plastic piece to pry the body panels off.</li><li>Flat head screw driver</li></ul><p>The entire installation takes takes about 2–3 hours to do. To fully realize the power gains a cat back exhaust is recommended along with a new tune to take advantage of the much improved air and exhaust flow. Plan on getting your car tuned to get the max performance out of your investment. Check out Cobb tuning in Austin, TX for the Access Port (DIY) tuner. Great off the self maps for this application. While IPD plenum is one of the “best bang for the buck” mods you can do, you should also look into catless or sport headers at the same time. Again off the shelf maps are available from Cobb to gradually update your car.</p><h3>Step 1</h3><p>Disconnect the battery cable. You do not want to be that guy going to Porsche dealership for $175 code removal. You will also be driving a Macan for a week at least here in Austin. This sucks so please don’t ignore this one…. Consider this as cash at hand before starting this project. Start by removing the oil/coolant cover assembly. Carefully pry the cover and pull straight up. I recommend using some plastic tool like a basic putty knife like the one pictured.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*r5ss6sfCZEue8ut2." /></figure><h3>Step 2</h3><p>Use your pry tool to do the same thing for the side panels on each side. Again pull straight out the car. Once you have the panels out make sure all the connectors are still firmly in the panel. If any are missing find them and place them back on the panel to make the assembly easier.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*CUdmOM4OCtfVHPqc." /></figure><h3>Step 3 — Carpet removal</h3><p>Remove the carpet from the top of the engine cover by pulling it straight back. It may take a bit of patience to get it out. Do not pull hard because you don’t want to damage any body panels still on top of the carpet.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*xBG8ljp5zoCW-jvX." /></figure><h3>Step 4</h3><p>Remove the top panel pieces (seat belt covers). They must be pulled to center of the car and up. They snap out quite easily. Again make sure all the clips are still attached to the panels. Do the same on the other side.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*6_JNry-8jHw1-ZfG." /></figure><h3>Step 5</h3><p>At this point of time you have exposed the mounting screws for the aluminum torsion bar. This bar needs to be removed to get access to the engine cover screws. Use Torx driver bit to back out the screws on both sides. Lift the torsion bar and the plastic cover under the torsion bar outside the car (not on the roof please!) to expose the front engine cover screws.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*u2vcR1jsgib1_jrs." /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*Q4bI2_7--S5jxwty." /></figure><h3>Step 6 (optional)</h3><p>This step is optional. Check if your toolbox has a Torx driver short enough to get the engine cover bolts off that are located directly underneath the cargo net loops. Fixed L -shaped Torx drivers will do. If not remove the cargo net loops on both sides. The screw securing them is accessible behind the carpet. This is easiest done thru the front doors rather than the trunk.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*g_LPIn6Rca8l6KOb." /></figure><h3>Step 7</h3><p>Remove all screws that secure the engine cover in place and then carefully lift the engine cover out of the engine bay. Be sure not to scrape your paint or interior pieces with the sharp edges when removing the cover.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*AW2FEM71ORmEnZMH." /></figure><h3>Step 8</h3><p>Next disconnect the vacuum line from the clamps (top arrows below) and unscrew the MAP (Manifold Absolute Pressure) sensor bolted on top of the intake plenum. Also remove the re-circulation system hose (bottom arrow) by pulling straight up.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*fYg1Zi2JakP63-hy." /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*X7twj-JLxVECVVta." /></figure><h3>Step 9</h3><p>Next remove the lower hose that connects to the plenum. This hose is located on the driver side of the plenum intake. See picture below.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*4NETAl5tg8ROfl7t." /></figure><h3>Step 10</h3><p>Remove the clamp that secures the rubber intake hose to the plenum. Use screw driver or specific hose tool to loosen up the rubber intake hose from the plenum.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*5lxvau8VdqUoGMIz." /></figure><h3>Step 11</h3><p>Disconnect the throttle body cable from the old throttle body. We will be removing the old throttle body while it is still attached to the intake so no need to loosen the throttle body from the intake.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*m5iCUN8Gf-lv41h2." /></figure><h3>Step 12</h3><p>Loosen up the two clamps that secure the plenum to the intake. Remove these clamps on both sides and lift them out of the engine bay. Be careful not to drop the bolts in the engine bay! You can leave the bottom half of the clamps hanging under the intake as we will deal with them later.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*8JURO1RcekY4_moO." /></figure><h3>Step 13</h3><p>Remove the vacuum line from behind of the intake. The arrow points to the vacuum line that needs to be removed.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*giZ7trWGr4J4xPYD." /></figure><h3>Step 14</h3><p>Move the rubber gasket inward on the plenum so that they completely clear the intake. Now you are ready to carefully lift the old plenum out of the car.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*zaAd29hxhwTZX9z4." /></figure><h3>Step 15</h3><p>Next you need to remove all the hardware to be reused with the IPD plenum. Unscrew the vacuum actuator illustrated below. Be extremely careful when removing the actuator arm. Mine broke and the ball head got stuck inside the actuator arm. I had to drill the stuck piece out to clear the actuator’s ball head to be used with the IPD plenum. I would recommend you spray some WD40 in it before even attempting to separate from the plenum.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*PI8Xlt4vISrFnenY." /></figure><h3>Step 16</h3><p>Transfer the vacuum actuator to the new plenum. Tighten the screws and pop the actual arm on the ball head on the new plenum.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*5MciBA_S0r6FWqYQ." /></figure><h3>Step 17</h3><p>Bolt the new GT3 intake to the IPD plenum and make sure you place rubber gasket in between. Transfer the rubber gaskets from the old plenum to the IPD plenum. The new plenum is now ready to installed back to the car.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*knpCWfgXJ3YoHqpJ." /></figure><h3>Stock Cayman 75mm vs. IPD 82mm GT3 throttle body for comparison.</h3><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*yJzJIv3mQZOtHTw1." /></figure><h3>Step 18</h3><p>Remove the old intake Y -pipe from the car. It is secured in place with 2 clamps. Remove these clamps using flat head screwdriver or 8mm socket. Pull the entire Y-pipe out of the car.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*M1_vh8JnhUaTe-xr." /></figure><h3>Step 19</h3><p>Install the new intake Y pipe. I recommend that you lubricate all 3 ends of the Y-pipe to make installation easier..</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*-nq9SGKIl1wpHIij." /></figure><p>Next position the clamps on the new Y-pipe and position it inside the car. The side that has IPD logo / text needs to be facing up. Next tighten the clamps to secure the Y pipe to the intake pipes coming from the air filters. In order to do this you need to look straight down and towards the end of the car.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*DJWcRt7XM2_Nu1yh." /></figure><h3>Step 20</h3><p>Locate the bottom half of the of plenum clamps and make sure they are roughly where they need to be. Next lift the new intake in the car. Move the rubber (plenum to intake) gaskets back into place and place the top half of the clamps back on. Secure the throttle body to the Y-pipe using the clamp from the stock Y-pipe.</p><p><strong>IMPORTANT!</strong> Use thread lock on the intake clamp bolts!!! I did not and clamps came loose causing MAP failure and I had to take the car apart again to fix the problem!</p><p>Verify that you have the rubber gasket properly positioned and that the clamps fit perfectly around them. This is important otherwise you will likely get service engine light. Next tighten intake clamps so that are pretty firm. No not over tighten! You may need to ask for assistant to compress the clamps so you can get the bolts back on. The plenum is now secured and we can hook up all the accessories back to it.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*B9roBd2Tke-evIb0." /></figure><ol><li>Y intake pipe to the plenum</li><li>Plenum to intake</li><li>Vacuum line to the vacuum actuator</li><li>Vacuum line to the clip</li><li>MAP Sensor to the intake</li><li>Re-circulation line to the plenum</li><li>Hose to the plenum</li><li>Throttle body connector</li></ol><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*ionAwkuHOWi0vZMy." /></figure><p>Step 21</p><p>Reconnect your battery and go test drive the car without the engine cover and make sure everything is working perfectly and that there are no service engine light. Try to exercise the entire rev range if possible. This will be one heck of a hot and wild sounding ride!</p><h3>Step 22</h3><p>Reinstall the engine cover and all the interior pieces. ENJOY!</p><h3>Additional NOTES</h3><p>You do not need to perform the Porsche throttle body adaptation process like many people in various forums claim. If you get service engine light in the first couple hundred miles this is normal but it should clear itself soon after and never come back. This caused by your car learning to adapt to the new increased airflow and while it is assuming you have the old throttle body the computer may initially think there is a problem with the intake or throttle body. If the check engine light comes and goes repeatably there is likely a problem with the installation. Scan the computer and get the codes. Anything related to MAP or Throttle body are sure signs of installation issues which is most likely caused by a hose / intake plenum leak somewhere. If this happens you need go back and make sure that all the clamps and hoses are still secured proper</p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=ad4cd601c68f" width="1" height="1" alt="">]]></content:encoded>
        </item>
    </channel>
</rss>