<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0" xmlns:cc="http://cyber.law.harvard.edu/rss/creativeCommonsRssModule.html">
    <channel>
        <title><![CDATA[Stories by Matt Collins on Medium]]></title>
        <description><![CDATA[Stories by Matt Collins on Medium]]></description>
        <link>https://medium.com/@matt.collins589?source=rss-793b90c26744------2</link>
        <image>
            <url>https://cdn-images-1.medium.com/fit/c/150/150/1*ODkpHr_6zBR2qtrPvPEJKA.jpeg</url>
            <title>Stories by Matt Collins on Medium</title>
            <link>https://medium.com/@matt.collins589?source=rss-793b90c26744------2</link>
        </image>
        <generator>Medium</generator>
        <lastBuildDate>Fri, 20 Nov 2026 09:21:49 GMT</lastBuildDate>
        <atom:link href="https://medium.com/@matt.collins589/feed" rel="self" type="application/rss+xml"/>
        <webMaster><![CDATA[yourfriends@medium.com]]></webMaster>
        <atom:link href="http://medium.superfeedr.com/" rel="hub"/>
        <item>
            <title><![CDATA[Airframe Drilling and Fastening Tools]]></title>
            <link>https://medium.com/@matt.collins589/airframe-drilling-and-fastening-tools-d9281b504068?source=rss-793b90c26744------2</link>
            <guid isPermaLink="false">https://medium.com/p/d9281b504068</guid>
            <category><![CDATA[aircraft-manufacturing]]></category>
            <category><![CDATA[aircraft-maintenance]]></category>
            <dc:creator><![CDATA[Matt Collins]]></dc:creator>
            <pubDate>Mon, 26 Oct 2026 14:03:11 GMT</pubDate>
            <atom:updated>2026-10-26T14:21:38.920Z</atom:updated>
            <content:encoded><![CDATA[<p>A Beginners Guide to Types, Purposes and Manufacturers</p><h3>Abstract</h3><p>A brief introduction for Aviation Maintenance Technician (AMT) students to the tools used to drill and fasten airframe structure, on sheet metal and on composites. For each tool it covers what the tool is for, how it fits into a repair, and who makes or sells it. It draws on the Federal Aviation Administration (FAA) airframe handbook and advisory circulars, U.S. Army and Air Force maintenance manuals, a military rivet specification, and published research on riveting vibration and composite drilling.</p><h3>From Drawing to Driven Rivet</h3><p>The handbook’s riveting procedure has three steps. You transfer and prepare the holes, drill them, and drive the rivets. Before a single rivet goes in, every hole has to line up and the parts have to be held together with temporary fasteners (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–39, 4–40). Hole quality matters because poor holes can start cracks in the airframe. Researchers measure it by surface roughness, burrs, size and roundness, and poor holes are a main reason parts are rejected at assembly (<a href="https://doi.org/10.1016/j.jmrt.2020.09.003">Aamir et al. 2020</a>, pp. 12485, 12486). The tools in this guide come in that order.</p><p>Rivet holes are drilled slightly larger than the rivet. A solid rivet swells to fill the hole when it is driven, and the joint’s strength depends on that swelled diameter, so the drill size for each rivet matters. The military buck-type rivet specification calls for drilling at 90 degrees to the surface without extreme pressure, and for holding the sheets together when drilling more than one (<a href="https://www.faa.gov/documentLibrary/media/Advisory_Circular/AC_43.13-1B_w-chg1.pdf">FAA AC 43.13–1B</a>, p. 4–11; <a href="https://www.vansaircraft.com/wp-content/uploads/2019/02/MIL-R-47196A_MI.pdf">MIL-R-47196A</a>, para. 3.2.1.1). On a real aircraft, hole sizes for anything other than common rivets come from the drawings or manuals for that job, and major repairs to stressed skin follow the manufacturer’s approved instructions (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–39, 4–40; <a href="https://www.faa.gov/documentLibrary/media/Advisory_Circular/AC_43.13-1B_w-chg1.pdf">FAA AC 43.13–1B</a>, p. 4–11).</p><h3>Drill Motors</h3><p>Pneumatic drill motors are the most common type for aircraft repair work. The handbook lists them as lightweight, with enough power and good speed control, and the handbook recommends them for repairs around flammable materials, where sparks from an electric drill motor might become a fire hazard (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–14; <a href="https://everyspec.com/ARMY/TM-Tech-Manual/TM_1-1500-204-23-9_CHG-4_50547/">Army TM 1–1500–204–23–9</a>, para. 5–7). That recommendation is about the power source only. It doesn’t make an air drill safe to use in a fuel tank or around fuel vapors. Work in those areas follows the aircraft maintenance manual and the shop’s own safety procedures. Most motors used for aircraft sheet metal work are rated at 3,000 rpm. For deep holes, or for hard materials such as corrosion resistant steel and titanium, the handbook says to select a motor with more torque and lower rpm to prevent damage to tools and materials (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–14). Brown Aviation Tool Supply lists pneumatic drills from Sioux and Dotco (<a href="https://www.browntool.com/Listview/tabid/344/CategoryID/335/Level/a/Default.aspx">Brown Aviation Tool Supply, drills</a>).</p><p>Check the bit before you drill. Run the motor freely and watch it, because a bit that wobbles or is slightly bent makes an oversize hole, a point Cherry Aerospace also makes in its CherryMAX process manual (<a href="https://www.cherryaerospace.com/docs/catalogs/CA-1015.pdf">Cherry Aerospace, CherryMAX Process Manual</a>, p. 7). The Air Force goes further and says a motor with a wobbly chuck or worn bearings shouldn’t be used at all (<a href="https://everyspec.com/USAF/USAF-Tech-Manuals/TO_1-1A1-A_15JAN2016_3992/">USAF T.O. 1–1A-1</a>, app. C.4). Hold the drill with both hands, keep it square to the work so you don’t oval the hole, and wear eye protection (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–14; <a href="https://everyspec.com/ARMY/TM-Tech-Manual/TM_1-1500-204-23-9_CHG-4_50547/">Army TM 1–1500–204–23–9</a>, para. 5–2). With air tools, look the hose over for cracks, blow out any water before you connect it, and shut off the air before you change a bit. Take the chuck key out as soon as you’ve tightened the bit, because a key left in the chuck flies out when the motor starts (<a href="https://everyspec.com/ARMY/TM-Tech-Manual/TM_1-1500-204-23-9_CHG-4_50547/">Army TM 1–1500–204–23–9</a>, para. 5–2, 5–7).</p><p>Straight drills have the chuck at one end and the air inlet at the other, and a 360-degree head rotates to point the bit almost anywhere (<a href="https://everyspec.com/ARMY/TM-Tech-Manual/TM_1-1500-204-23-9_CHG-4_50547/">Army TM 1–1500–204–23–9</a>, para. 5–7). Right angle and 45-degree motors reach positions a pistol grip can’t. Most right angle models take threaded bits, and heavy-duty ones have a chuck like a pistol grip drill (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–14). Jiffy makes a 90-degree threaded drill that Brown also lists (<a href="https://www.browntool.com/Listview/tabid/344/CategoryID/335/Level/a/Default.aspx">Brown Aviation Tool Supply, drills</a>). A two-hole nutplate drill cuts both rivet holes at once, so the spacing matches the nutplate (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–15). On a drill press you clamp the part to the table first, because an unclamped part can grab the drill and spin, and the handbook warns that this can cost fingers or hands (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–15).</p><p>Where access is poor, an extension bit, an angle adapter that fits the chuck of a straight drill, or a flexible snake attachment gets the bit to the work. Hold the drill in one hand and the adapter in the other so the adapter doesn’t spin (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–16).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/997/1*tHKzvV84Awm3us9cw8Fv6g.jpeg" /><figcaption>Pneumatic drill motors (FAA-H-8083–31B, Fig. 4–39).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/925/1*WuDVzssktENdKBU3DI6uag.png" /><figcaption>Pneumatic drill types (TM 1–1500–204–23–9, Fig. 5–15).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/997/1*ZW52BmgJHGkxRFHa5dadrA.jpeg" /><figcaption>Angle drill motors (FAA-H-8083–31B, Fig. 4–40).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/997/1*Qn9_2b1_Au1otyFxqmji1A.jpeg" /><figcaption>Nutplate drill (FAA-H-8083–31B, Fig. 4–41).</figcaption></figure><h3>Drill Bits and Drilling Aids</h3><p>Drill sizes come in number, letter and fractional series (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–17, 4–18). The handbook gives these finished hole sizes for common rivets (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–39).</p><ul><li><strong>3/32.</strong> Drill for the finished hole: #40.</li><li><strong>1/8.</strong> Drill for the finished hole: #30.</li><li><strong>5/32.</strong> Drill for the finished hole: #21.</li><li><strong>3/16.</strong> Drill for the finished hole: #11.</li><li><strong>1/4.</strong> Drill for the finished hole: F.</li></ul><p>The standard twist bits for aluminum are high speed steel (HSS) with a 135-degree split point (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–17). A 2020 review of aerospace aluminum drilling explains why HSS is the usual choice. It is widely available, low in cost and tough, while carbide is harder. The same review recommends a 130 to 140 degree point for aluminum alloys with little or no silicon, and notes that a larger point angle helps reduce burrs (<a href="https://doi.org/10.1016/j.jmrt.2020.09.003">Aamir et al. 2020</a>, p. 12488). Titanium and stainless wear HSS out quickly, so those metals call for cobalt bits. The handbook adds that cobalt doesn’t produce a quality hole in aluminum alloys (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–17). A step drill pairs a small pilot point with a larger cutting step. For bigger holes in general, the handbook starts with a №40 or №30 pilot and opens the hole up to size (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–16).</p><p>A spring drill stop keeps the bit from plunging through into whatever is behind the sheet and keeps the chuck from marking the skin (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–17). A drill bushing is a hardened guide set in a holder that keeps the drill square to the part. The holder types are in the table below (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–19). Factories use drilling jigs for the same reason. Fastener holes there are often drilled with handheld air drills, and the jig puts the drill on the right spot, keeps the hole square to the mating parts and limits wander from vibration (<a href="https://doi.org/10.1016/j.jmrt.2020.09.003">Aamir et al. 2020</a>, p. 12485).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/913/1*dp9_4S73qes6hInNzz6e6A.png" /><figcaption>Parts of a twist drill (TM 1–1500–204–23–9, Fig. 4–83).</figcaption></figure><ul><li><strong>Standard.</strong> Where it’s used: Flat stock or tubing and rod, with insert-type bushings.</li><li><strong>Egg cup.</strong> Where it’s used: Flat and curved material. An improved tripod base with interchangeable bushings.</li><li><strong>Plate.</strong> Where it’s used: Interchangeable production parts, with commercial bushings and self-feeding drills.</li><li><strong>Arm.</strong> Where it’s used: Critical structure. Locks in position and takes interchangeable commercial bushings.</li></ul><figure><img alt="" src="https://cdn-images-1.medium.com/max/690/1*LnuX3Je5TTZSukTt7TP1FA.png" /><figcaption>Bushing holder and arm-type bushing holder (FAA-H-8083–31B, Fig. 4–50).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/992/1*pUhfDgQZgS3kTPKxyX-2ig.jpeg" /><figcaption>Drilling through a bushing holder held against the skin (FAA-H-8083–31B, Fig. 4–51).</figcaption></figure><h3>Clecos and Temporary Fasteners</h3><p>Sheets that aren’t held tight separate while they are drilled and riveted, so reusable temporary fasteners hold the drilled parts in position until the rivets go in. The Cleco is the most commonly used sheet metal holder in the handbook. It has a steel cylinder body with a plunger on top, a spring, a pair of step-cut locks and a spreader bar. Clecos come in six diameters, 3/32, 1/8, 5/32, 3/16, 1/4 and 3/8 inch, with the size stamped on the fastener and a color code for quick recognition. One style of Cleco pliers fits all six sizes. You push the fastener into a drilled hole with the pliers, and when it is installed correctly it keeps the holes in the separate sheets aligned (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–28, 4–29).</p><p>Hex nut and wing nut fasteners are used instead when more clamp-up pressure is needed. The handbook gives up to 300 pounds of clamping force for the hex nut type, which a hex nut runner installs and removes quickly, and 0 to 300 pounds for the wing nut type, which you turn by hand. A Cleco hex nut fastener can also be run with a pneumatic Cleco installer (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–29).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/938/1*fJKl4y18lWIoHqi4Lj2DOQ.jpeg" /><figcaption>Cleco fastener, extended and retracted (Photo: Thermofan, Wikimedia Commons, CC0).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1000/1*mQYzHoFz2F9ETFyjqCqZ8Q.jpeg" /><figcaption>Cleco pliers (Photo: Thermofan, Wikimedia Commons, CC0).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/997/1*5FwJh7B46j4X-47EMBsxSw.jpeg" /><figcaption>Hex nut temporary fastener (FAA-H-8083–31B, Fig. 4–73).</figcaption></figure><p>Buying tools one at a time is expensive, and students in the US can save by buying a kit or buying used. Yardstore in Wichita, Kansas, began in 1946 selling Beech Aircraft’s excess property and now stocks new, surplus and used aircraft sheet metal tools, including Cherry and Huck tools (<a href="https://www.yardstore.com/about-us">Yardstore, About Us</a>). For a first set, its master sheet metal tool kits bundle an ACAT 2X, 3X or 4X rivet gun with rivet sets, bucking bars, Clecos, clamps and drills (<a href="https://www.yardstore.com/aircraft-sheet-metal-tool-kits">Yardstore, sheet metal tool kits</a>). Its smaller kits cover single jobs, such as flush rivet sets, drill bushings and countersink cages (<a href="https://www.yardstore.com/aircraft-sheet-metal-tool-kits/miscellaneous-tool-kits">Yardstore, tool kits</a>). Brown Aviation Tool Supply sells used Clecos it describes as surplus from a major aircraft factory, at about half the price of new ones (<a href="https://www.browntool.com/Listview/tabid/344/ProductID/4115/Default.aspx">Brown Aviation Tool Supply, used Clecos</a>). Bulk lots of used Clecos also turn up on eBay. Check each one before it goes in a hole. The plunger shouldn’t be pushed in, the locking step should still be sharp and square, and some in a lot may be gummed with sealant and need cleaning.</p><h3>Deburring, Reaming, Countersinking and Dimpling</h3><p>Every drilled hole leaves a burr, and it has to come off so the rivet seats snugly and the burr doesn’t scratch the part (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–14). A bearing scraper removes it, as does a countersink or an oversize drill bit turned by hand (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–14). A chip chaser, a flexible hooked steel blade on a plastic handle, pulls out chips and burrs caught between the sheets (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–19).</p><p>A reamer opens a hole to an exact size and leaves a smooth wall. Reamers come in bullet, straight and piloted styles. Don’t back one out in reverse, because it drags chips into the wall. Keep it turning in the cutting direction as you pull it out (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–17; <a href="https://everyspec.com/USAF/USAF-Tech-Manuals/TO_1-1A1-A_15JAN2016_3992/">USAF T.O. 1–1A-1</a>, app. C.3).</p><p>Flush rivets need a seat for the head, either cut into the skin (countersinking) or pressed into it (dimpling). A countersink cuts a cone-shaped recess to match the rivet head. The most commonly used type has an included angle of 100 degrees, and 82 and 120 degree cutters are sometimes used (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–36, 4–41). A six-flute cutter works best in aluminum. Three- and four-flute cutters are harder to control for chatter, and corrosion resistant steel calls for a single-flute cutter of the kind Weldon Tool makes (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–41). How deep to cut depends on the job. The countersink should be cut only deep enough for the rivet head and metal to form a flush surface, and the handbook notes that countersinking removes material, which can call for more fasteners and greater edge distance than universal head fasteners. A countersink that is too deep leaves a knife edge, and countersunk holes have been responsible for fatigue cracks in pressurized skin. For primary structure and pressurized skin repairs, the handbook reports that some manufacturers recommend a depth of no more than 2/3 of the outer sheet thickness or down to 0.020-inch minimum fastener shank depth, whichever is greater. For the figure that applies to a given repair, follow the structural repair manual or the manufacturer’s instructions (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–40).</p><p>The FAA handbook calls the microstop countersink the preferred countersinking tool, and it is sold as a countersink cage (<a href="https://aircraftspruce.com/catalog/pnpages/12-00940.php">Aircraft Spruce, countersink cage</a>). Its adjustable-sleeve cage works as a depth stop and holds the revolving cutter vertical, and a removable or integral pilot keeps the cutter centered. The handbook sets the pilot at about 0.002 inch smaller than the hole and recommends testing the adjustment on scrap before cutting a repair or replacement part (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–41). The military rivet specification requires a countersink tool with an automatic stop, used at 90 degrees and leaving no chatter marks (<a href="https://www.vansaircraft.com/wp-content/uploads/2019/02/MIL-R-47196A_MI.pdf">MIL-R-47196A</a>, para. 3.2.1.4). Where a microstop can’t fit, countersinking is done freehand, which the handbook says to practice on scrap, holding the drill as steady and perpendicular as when drilling. Chatter is the most common problem, and the handbook’s remedies include sharp tooling, slow speed with steady firm pressure, a piloted cutter and a different number of flutes (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–41).</p><p>Your test rivet on scrap tells you which way to adjust the stop. A head that sits proud means the countersink is too shallow, and a head below the skin means it’s too deep. A hole cut too deep can’t be fixed by resetting the stop, because the metal is already gone (<a href="https://www.wesconusa.com/kb/KB4136/flush-rivets-microstop-countersink-depth">Wescon KB4136</a>).</p><p>Countersink cages and their threaded cutters are sold separately. Wescon Industries makes countersink cages in swivel and extended-reach versions for imperial and metric cutter threads (<a href="https://www.wesconusa.com/products/catalogs/microstop-countersink-cage">Wescon Industries, countersink cages</a>). Magnavon cages are now mostly found used, and surplus sellers such as Yardstore list Magnavon cages and kits in used and surplus-new condition, with cutter capacities up to 1 1/4 inch (<a href="https://www.yardstore.com/surplus/drilling-and-cutting/microstops">Yardstore, surplus microstops</a>). Zephyr Tool Group (<a href="https://zephyrtoolgroup.com/zephyr-aerospace/microstop-countersink-cages-countersink-cutters">Zephyr Tool Group, countersink cages</a>) and Snap-on (<a href="https://www.snapon.com/Aviation/Aviation-Tools/Structure-Tools.htm">Snap-on, aviation structure tools</a>) also make them. Aircraft Spruce lists a typical cage that adjusts in 0.001-inch steps and takes 1/4–28 threaded cutters (<a href="https://aircraftspruce.com/catalog/pnpages/12-00940.php">Aircraft Spruce, countersink cage</a>).</p><p>Dimpling presses the seat with a male and female die and removes no metal. A dimpled joint reduces the shear loading on the rivet and places more load on the riveted sheets. The handbook requires dimpling for sheets thinner than the minimum specified thickness for countersinking, but it is not limited to thin material. The temper of the material, the rivet size and the available equipment all bear on the choice. You need one die set for each rivet size and head shape, struck with a hammer or run in a squeezer. Some alloys crack when dimpled cold. The handbook says 2024-T3 can be dimpled hot or cold but may crack near the dimple after cold dimpling, and that 7075-T6, magnesium alloys and titanium are hot dimpled with heated dies (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–41, 4–42, 4–43).</p><h3>Driving Solid Rivets</h3><p>One person runs the rivet gun on the head side while the bucker holds a bar against the tail, and on a two-person team they signal each other by tapping (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–40).</p><p>The handbook sizes rivet guns on the old Chicago Pneumatic “X” series, by the largest rivet size the gun drives continuously. A 4X gun (dash 8, or 1/4 inch rivet) is used for normal work, a 3X gun for smaller rivets in thinner structure, and a 7X gun for large rivets in thicker structure. The commonly used slow hitting guns strike 900 to 2,500 blows per minute. A gun that is too powerful is hard to control and may damage the work, and one that is too light may work harden the rivet before the head fully forms, so if the adjustment doesn’t give the right driving force a different sized gun is needed. A rivet should upset in 1 to 3 seconds (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–37, 4–38). Brown Aviation Tool Supply lists Sioux and Chicago Pneumatic guns from 2X to 5X (<a href="https://www.browntool.com/Listview/tabid/344/CategoryID/36/Level/a/Default.aspx">Brown Aviation Tool Supply, rivet guns</a>), and Chicago Pneumatic’s current CP42 rivet hammer series runs from 1X to 9X (<a href="https://tools.cp.com/en/products/cp42-series-rivet-hammers-sku23690">Chicago Pneumatic, CP42 rivet hammers</a>).</p><p>Install the correct rivet set and the retaining spring, then test the gun on a piece of wood and adjust the air valve to a setting that is comfortable. The needle valve on the handle sets the driving force, and the adjustment should never be tested against anything harder than a wooden block, to avoid damaging the set. Never point a rivet gun at anyone. Don’t pull the trigger unless the set is against a rivet or the wood, and disconnect the hose when you put the gun down (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–38). Rivet guns also shake your hands, and reduced-vibration guns and bucking bars exist to cut the risk of carpal tunnel syndrome (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–38). When the National Institute for Occupational Safety and Health (NIOSH) tested eight pneumatic riveting hammers in the lab and on aircraft riveting jobs, four of them came out consistently lower in vibration (<a href="https://doi.org/10.1093/annhyg/mes022">McDowell et al. 2012</a>).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1000/1*ZAL6dlh0-2INfM91CMMk6Q.jpeg" /><figcaption>A riveting team on a C-47 cockpit shell, North American Aviation (Photo: Alfred T. Palmer, Wikimedia Commons, public domain).</figcaption></figure><p>The bucking bar is a heavy piece of steel, also called a dolly or bucking block, held against the rivet’s tail while the shop head forms. The handbook calls for a bar of the proper weight and the right shape, because the wrong shape deforms the head (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–35, 4–38). The force of the gun has to be absorbed by the bar and not by the structure. In a NIOSH study at Tinker Air Force Base, tungsten bars vibrated less than steel bars of the same shape (<a href="https://stacks.cdc.gov/view/cdc/201020">McDowell et al. 2014</a>). Snap-on makes its bars with rounded edges and polished faces so they don’t scratch the skin (<a href="https://www.snapon.com/Aviation/Aviation-Tools/Structure-Tools.htm">Snap-on, aviation structure tools</a>).</p><ul><li><strong>Rivet set (header).</strong> Fits in the gun and has to match the rivet head, because one too small marks the rivet and one too large marks the skin. A short straight set suits places the gun can reach, and offset and long sets reach rivets behind structure (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–38).</li><li><strong>Rivet squeezer.</strong> Upsets a rivet by compression near an edge, with one fixed jaw acting as the bucking bar, so one person can work alone. Hand, pneumatic and pneudraulic types all work only where the yoke reaches (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–38). Cleaveland Aircraft Tool makes a hand squeezer and lists the Numatx 3K hydraulic system (<a href="https://www.cleavelandtool.com/shop/snmtx3k-numatx-3k-squeezer-system-no-yoke-162">Cleaveland Aircraft Tool, Numatx squeezer</a>).</li><li><strong>Hand rivet set and draw set.</strong> The hand set drives a particular rivet type with a hammer, and the draw set pulls the sheets together to close a gap before you buck the rivet (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–36).</li><li><strong>Rivet cutter.</strong> Trims rivets to length when the right size isn’t on hand. Diagonal cutters can also do it (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–35).</li><li><strong>Microshaver.</strong> Trims a countersunk head flush where the skin has to be smooth to a tolerance. Adjust it on scrap first (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–39).</li></ul><p>USATCO is one supplier of guns, sets, bars and squeezers (<a href="https://usatco.com/solid-riveting-tools/">USATCO, solid riveting tools</a>).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/991/1*D1nQtW7Of_8PnaLsOQmpeQ.jpeg" /><figcaption>Pneumatic rivet guns (FAA-H-8083–31B, Fig. 4–86).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/996/1*Hb1KegZGkPga0bOvpV42lQ.jpeg" /><figcaption>Rivet sets (FAA-H-8083–31B, Fig. 4–88).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/993/1*qHdN-mPcGu-smBfIBdUyMg.jpeg" /><figcaption>Bucking bars (FAA-H-8083–31B, Fig. 4–83).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1000/1*rZ93Mcii7cdcAz6Z2KFriQ.jpeg" /><figcaption>A U.S. Navy airman adjusts a rivet squeezer aboard USS Carl Vinson (U.S. Navy photo, Wikimedia Commons, public domain).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/754/1*kqGmbpTUS1ToMFld1PmHcQ.jpeg" /><figcaption>Hand rivet squeezer (FAA-H-8083–31B, Fig. 4–93).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/997/1*pDAEqfPq88UcHjJFICu_yA.jpeg" /><figcaption>Rivet cutter (FAA-H-8083–31B, Fig. 4–82).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/996/1*3BYCS0Ubt0kZU4gmbnARoA.jpeg" /><figcaption>Microshaver (FAA-H-8083–31B, Fig. 4–89).</figcaption></figure><h3>Blind Rivets, Hi-Loks and Lockbolts</h3><p>When a bucking bar can’t be placed behind the rivet, a blind fastener is installed from one side, and each kind needs its own installation tools (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–45). Cherry Rivet Company introduced the first blind fasteners in 1940, and as Cherry Aerospace it still makes many of them, along with Alcoa Fastening Systems. Their tooling often isn’t interchangeable, so match the tool to the rivet (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–47).</p><ul><li><strong>Pulling-type rivet gun.</strong> Draws the stem of a blind rivet up into its hollow sleeve, which forms a tail on the far side and clamps the sheets together (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–47). Cherry recommends its single action riveter for CherryMAX rivets, and where CherryMAX rivets go into dimpled thin sheet it calls for reaming the hole to size after dimpling, because dimpling stretches the pilot hole (<a href="https://www.cherryaerospace.com/docs/catalogs/CA-1015.pdf">Cherry Aerospace, CherryMAX Process Manual</a>, pp. 4, 9).</li><li><strong>Hand and pneumatic-hydraulic riveters.</strong> The hand riveter is a hand-powered puller, and the air-powered pneumatic-hydraulic version serves production and larger jobs. For CherryMAX rivets the handbook names Cherry’s G750A or G800 by hand and the G704B or G747 by air (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–48).</li><li><strong>High-shear gun set.</strong> Fits an ordinary rivet gun to swage and trim the collar of a high-shear rivet, with a standard bucking bar. A separate set is needed for each shank diameter (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–49).</li><li><strong>Hi-Lok tools.</strong> An Allen wrench holds the pin through a hex recess in its end while the driving tool turns the collar. The collar’s wrenching flats snap off at the specified torque (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–50; <a href="https://everyspec.com/USAF/USAF-Tech-Manuals/TO_1-1A1-A_15JAN2016_3992/">USAF T.O. 1–1A-1</a>, para. 5.3.1.1.7). Hi-Lok, Hi-Tigue and Hi-Lite are made by Hi-Shear Corporation (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 4–50). Howmet Aerospace lists frangible collar installation tools for Hi-Lok collars among its fastening system tools (<a href="https://www.howmet.com/products/aerospace/installation-tools/">Howmet Aerospace, installation tools</a>).</li><li><strong>Lockbolt tools.</strong> A pull gun installs a pull-type lockbolt, often called a huckbolt, as a one-person job. A stump-type lockbolt is driven with a riveting hammer and bucking bar and takes two people. Lockbolts have their own grip gauge for picking the length (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 4–51, 4–52; <a href="https://everyspec.com/USAF/USAF-Tech-Manuals/TO_1-1A1-A_15JAN2016_3992/">USAF T.O. 1–1A-1</a>, para. 5.3.1.1.6).</li></ul><h3>Tools for Composite Structure</h3><p>Air-driven drills, routers and grinders are used on composites, because carbon conducts electricity and can short out an electric motor. Any electric tool has to be the totally enclosed type (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–19).</p><ul><li><strong>Drill bit.</strong> Metal structure: HSS, cobalt for titanium and stainless. Composite structure: Diamond-coated or solid carbide for carbon fiber and fiberglass.</li><li><strong>Drill speed.</strong> Metal structure: Most motors rated around 3,000 rpm. Composite structure: General range of 2,000 to 20,000 rpm with a low feed. Exact settings come from the SRM or cutter data.</li><li><strong>Countersink cutter.</strong> Metal structure: Six-flute for aluminum. Composite structure: Carbide for carbon/epoxy.</li><li><strong>Permanent fasteners.</strong> Metal structure: Solid rivets, blind rivets, Hi-Loks, lockbolts. Composite structure: Mostly Hi-Loks or Huck-Spin lockbolts in primary structure.</li></ul><p>(FAA-H-8083–31B, pp. 4–14 to 4–52 and 7–46 to 7–52)</p><p>The handbook says not to use standard twist bits on composite structure. Standard HSS dulls immediately, generates excessive heat, and causes ply delamination, fiber tear-out and unacceptable hole quality. Carbon/epoxy is hard and abrasive, so the bits for carbon fiber and fiberglass are diamond-coated or solid carbide, and even those wear fast (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–50). Kevlar is different. Its fibers fray under a standard bit, and the handbook prefers the sickle-shaped Klenk drill, which grabs the fibers and shears them cleanly, although standard twist drills can be used when the Kevlar/epoxy part is sandwiched between two metal parts (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–50). A review of composite drilling research found that ordinary tungsten carbide drills have a short life in carbon fiber and pointed to polycrystalline diamond (PCD) tools as a promising alternative (<a href="https://doi.org/10.3389/fmats.2022.990773">Xu 2022</a>).</p><p>Speed and feed also differ from metal. The handbook gives 2,000 to 20,000 rpm with a low feed rate as the general range for drilling composites. It isn’t a setting for every cutter, laminate or hole size, and the speed and feed for a given repair come from the structural repair manual or the cutter manufacturer’s data. A drill motor with power feed or a hydraulic dash pod restricts the surging of the drill as it exits the material, which reduces breakout damage and delamination. Parts made from tape products are especially susceptible to breakout, and the structure needs to be backed with a metal plate or sheet. Titanium behaves the other way, because it is drilled at low speed and high feed, and bits suited to titanium might not suit carbon or fiberglass (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, pp. 7–50, 7–51). Drill guides are recommended, especially for thicker laminates (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–50).</p><p>Holes in composite structure are often predrilled with a small pilot hole, opened with a diamond-coated or carbide bit and reamed to size with a carbide reamer. Small HSS bits such as a №40 are still used to pilot by hand, because carbide is brittle and breaks easily, even though an HSS bit may last for only one hole (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–51). Carbide cutters cut flush fastener seats in carbon/epoxy (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–51). The handbook calls it good practice to run a vacuum while drilling so carbon dust doesn’t float around the work area (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–51).</p><p>On composite structure the permanent fasteners are mostly Hi-Loks and Huck-Spin lockbolts, and both the Hi-Lok and the pull-type Huck-Spin can be installed by one technician from one side (<a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">FAA-H-8083–31B</a>, p. 7–46).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/987/1*aiYL002DuGGFe2ELtXHNBA.jpeg" /><figcaption>Drilling and cutting tools for composites (FAA-H-8083–31B, Fig. 7–86).</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/987/1*5fG14Sk83z5s1rDbPM8EGg.jpeg" /><figcaption>Autofeed drill (FAA-H-8083–31B, Fig. 7–87).</figcaption></figure><h3>Sources</h3><p>Federal Aviation Administration, <em>Aviation Maintenance Technician Handbook, Airframe</em>, FAA-H-8083–31B, U.S. Department of Transportation, Flight Standards Service, 2023. <a href="https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf">https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/FAA-H-8083-31B_Aviation_Maintenance_Technician_Handbook.pdf</a></p><p>Brown Aviation Tool Supply, “Drills, Pneumatic,” product category listing. <a href="https://www.browntool.com/Listview/tabid/344/CategoryID/335/Level/a/Default.aspx">https://www.browntool.com/Listview/tabid/344/CategoryID/335/Level/a/Default.aspx</a>. Accessed October 25, 2026.</p><p>Brown Aviation Tool Supply, “Rivet Guns,” product category listing. <a href="https://www.browntool.com/Listview/tabid/344/CategoryID/36/Level/a/Default.aspx">https://www.browntool.com/Listview/tabid/344/CategoryID/36/Level/a/Default.aspx</a>. Accessed October 25, 2026.</p><p>U.S. Air Tool Co. (USATCO), “Solid Riveting Tools.” <a href="https://usatco.com/solid-riveting-tools/">https://usatco.com/solid-riveting-tools/</a>. Accessed October 25, 2026.</p><p>Cleaveland Aircraft Tool, “Numatx 3K Squeezer System, No Yoke.” <a href="https://www.cleavelandtool.com/shop/snmtx3k-numatx-3k-squeezer-system-no-yoke-162">https://www.cleavelandtool.com/shop/snmtx3k-numatx-3k-squeezer-system-no-yoke-162</a>. Accessed October 25, 2026.</p><p>Federal Aviation Administration, <em>Acceptable Methods, Techniques, and Practices: Aircraft Inspection and Repair</em>, Advisory Circular 43.13–1B with Change 1, 1998. <a href="https://www.faa.gov/documentLibrary/media/Advisory_Circular/AC_43.13-1B_w-chg1.pdf">https://www.faa.gov/documentLibrary/media/Advisory_Circular/AC_43.13-1B_w-chg1.pdf</a></p><p>T. W. McDowell, C. Warren, D. E. Welcome and R. G. Dong, “Laboratory and Field Measurements and Evaluations of Vibration at the Handles of Riveting Hammers,” <em>Annals of Occupational Hygiene</em>, Vol. 56, №8, 2012, pp. 911–924. doi:10.1093/annhyg/mes022</p><p>T. W. McDowell, C. Warren, D. E. Welcome, X. S. Xu and R. G. Dong, “Laboratory and Field Measurements of Bucking Bar Vibrations,” <em>Proceedings of the Fifth American Conference on Human Vibration</em>, University of Guelph, Guelph, Ontario, 2014, pp. 63–64. <a href="https://stacks.cdc.gov/view/cdc/201020">https://stacks.cdc.gov/view/cdc/201020</a></p><p>J. Xu, “A Review on Tool Wear Issues in Drilling CFRP Laminates,” <em>Frontiers in Materials</em>, Vol. 9, 2022, Article 990773. doi:10.3389/fmats.2022.990773</p><p>Department of the Army, <em>Aviation Unit and Aviation Intermediate Maintenance Manual: General Aircraft Maintenance (Tools and Ground Support Equipment)</em>, Vol. 9, TM 1–1500–204–23–9, 1992, with Change 4, 2001. <a href="https://everyspec.com/ARMY/TM-Tech-Manual/TM_1-1500-204-23-9_CHG-4_50547/">https://everyspec.com/ARMY/TM-Tech-Manual/TM_1-1500-204-23-9_CHG-4_50547/</a></p><p>U.S. Air Force and U.S. Navy, <em>Engineering Handbook Series for Aircraft Repair: General Manual for Structural Repair</em>, T.O. 1–1A-1 / NAVAIR 01–1A-1, 2016. <a href="https://everyspec.com/USAF/USAF-Tech-Manuals/TO_1-1A1-A_15JAN2016_3992/">https://everyspec.com/USAF/USAF-Tech-Manuals/TO_1-1A1-A_15JAN2016_3992/</a></p><p>U.S. Army Missile Command, <em>Rivets, Buck Type, Preparation for and Installation of</em>, MIL-R-47196A(MI), 1977. <a href="https://www.vansaircraft.com/wp-content/uploads/2019/02/MIL-R-47196A_MI.pdf">https://www.vansaircraft.com/wp-content/uploads/2019/02/MIL-R-47196A_MI.pdf</a></p><p>Aircraft Spruce, “Micro-Stop Countersink Cage,” Part 12–00940. <a href="https://aircraftspruce.com/catalog/pnpages/12-00940.php">https://aircraftspruce.com/catalog/pnpages/12-00940.php</a>. Accessed October 25, 2026.</p><p>Wescon Industries, “Countersink Cages (Microstops).” <a href="https://www.wesconusa.com/products/catalogs/microstop-countersink-cage">https://www.wesconusa.com/products/catalogs/microstop-countersink-cage</a>. Accessed October 25, 2026.</p><p>Wescon Industries Engineering Team, “Rivets Not Flush? How to Set Microstop Countersink Depth,” Knowledge Base KB4136, updated October 19, 2026. <a href="https://www.wesconusa.com/kb/KB4136/flush-rivets-microstop-countersink-depth">https://www.wesconusa.com/kb/KB4136/flush-rivets-microstop-countersink-depth</a></p><p>Cherry Aerospace, “CherryMAX Process Manual,” CA-1015, Rev. C, February 3, 2015. <a href="https://www.cherryaerospace.com/docs/catalogs/CA-1015.pdf">https://www.cherryaerospace.com/docs/catalogs/CA-1015.pdf</a>. Accessed October 25, 2026.</p><p>Chicago Pneumatic, “CP42 Series Rivet Hammers.” <a href="https://tools.cp.com/en/products/cp42-series-rivet-hammers-sku23690">https://tools.cp.com/en/products/cp42-series-rivet-hammers-sku23690</a>. Accessed October 25, 2026.</p><p>Howmet Aerospace, “Fastening Systems Installation Tools.” <a href="https://www.howmet.com/products/aerospace/installation-tools/">https://www.howmet.com/products/aerospace/installation-tools/</a>. Accessed October 25, 2026.</p><p>Zephyr Tool Group, “Microstop Countersink Cages &amp; Countersink Cutters.” <a href="https://zephyrtoolgroup.com/zephyr-aerospace/microstop-countersink-cages-countersink-cutters">https://zephyrtoolgroup.com/zephyr-aerospace/microstop-countersink-cages-countersink-cutters</a>. Accessed October 25, 2026.</p><p>Snap-on Industrial, “Structure Tools,” Aviation Tools. <a href="https://www.snapon.com/Aviation/Aviation-Tools/Structure-Tools.htm">https://www.snapon.com/Aviation/Aviation-Tools/Structure-Tools.htm</a>. Accessed October 25, 2026.</p><p>Yardstore, “About Us.” <a href="https://www.yardstore.com/about-us">https://www.yardstore.com/about-us</a>. Accessed October 25, 2026.</p><p>Yardstore, “Miscellaneous Tool Kits.” <a href="https://www.yardstore.com/aircraft-sheet-metal-tool-kits/miscellaneous-tool-kits">https://www.yardstore.com/aircraft-sheet-metal-tool-kits/miscellaneous-tool-kits</a>. Accessed October 25, 2026.</p><p>Brown Aviation Tool Supply, “Used Cleco Fasteners.” <a href="https://www.browntool.com/Listview/tabid/344/ProductID/4115/Default.aspx">https://www.browntool.com/Listview/tabid/344/ProductID/4115/Default.aspx</a>. Accessed October 25, 2026.</p><p>Yardstore, “Aircraft Sheet Metal Tool Kits.” <a href="https://www.yardstore.com/aircraft-sheet-metal-tool-kits">https://www.yardstore.com/aircraft-sheet-metal-tool-kits</a>. Accessed October 25, 2026.</p><p>Yardstore, “Microstops,” Surplus Items, Drilling and Cutting. <a href="https://www.yardstore.com/surplus/drilling-and-cutting/microstops">https://www.yardstore.com/surplus/drilling-and-cutting/microstops</a>. Accessed October 25, 2026.</p><p>M. Aamir, K. Giasin, M. Tolouei-Rad and A. Vafadar, “A Review: Drilling Performance and Hole Quality of Aluminium Alloys for Aerospace Applications,” <em>Journal of Materials Research and Technology</em>, Vol. 9, №6, 2020, pp. 12484–12500. <a href="https://doi.org/10.1016/j.jmrt.2020.09.003">https://doi.org/10.1016/j.jmrt.2020.09.003</a></p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=d9281b504068" width="1" height="1" alt="">]]></content:encoded>
        </item>
    </channel>
</rss>