<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0" xmlns:cc="http://cyber.law.harvard.edu/rss/creativeCommonsRssModule.html">
    <channel>
        <title><![CDATA[vancilando - Medium]]></title>
        <description><![CDATA[We are two 30-somethings writing about building and traveling in our adventure van. - Medium]]></description>
        <link>https://medium.com/vancilando?source=rss----4a4b65ac3c80---4</link>
        <image>
            <url>https://cdn-images-1.medium.com/proxy/1*TGH72Nnw24QL3iV9IOm4VA.png</url>
            <title>vancilando - Medium</title>
            <link>https://medium.com/vancilando?source=rss----4a4b65ac3c80---4</link>
        </image>
        <generator>Medium</generator>
        <lastBuildDate>Thu, 19 Nov 2026 11:42:18 GMT</lastBuildDate>
        <atom:link href="https://medium.com/feed/vancilando" rel="self" type="application/rss+xml"/>
        <webMaster><![CDATA[yourfriends@medium.com]]></webMaster>
        <atom:link href="http://medium.superfeedr.com/" rel="hub"/>
        <item>
            <title><![CDATA[VAN BUILD: Ceiling + upper shelves]]></title>
            <link>https://medium.com/vancilando/van-build-ceiling-upper-shelves-4b45150416e4?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/4b45150416e4</guid>
            <category><![CDATA[van-build]]></category>
            <category><![CDATA[vanlife]]></category>
            <category><![CDATA[diy]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Wed, 03 Jul 2019 18:52:22 GMT</pubDate>
            <atom:updated>2019-07-03T18:52:22.772Z</atom:updated>
            <content:encoded><![CDATA[<h3>Ceiling</h3><p>The ceiling was a fun challenge. We debated going with three 1/4&quot; ply panels for ease of install and lighter weight, but in the end the pine tongue-and-groove won us over. It also allowed us to follow the curve of the roof and was strong enough to cantilever to the end while not bowing in the middle.</p><p>I prepped the boards by sanding and sealing both sides with water-based polycrylic. We opted for water-based on these as well as the countertops because it doesn’t bring out the yellow as much as an oil-based would and leaves the wood as close to its natural color as possible. It was pretty exciting maneuvering these 12&#39; boards around in the shop, but we made it work! Spencer installed some 1/2&quot; plywood furring on the van ribs to provide an attachment surface for the screws and create a tiny gap between the insulation panels and the ceiling boards.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*NlL-IZyRxE-9_jgDs7AC6A.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*LY2rJVXChiD6AiBbLKj9eg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*1vYms1PSIexO6ZMgJldFGA.jpeg" /></figure><p>Next, Dave and Spencer began the task of installing the ceiling boards in the van. This required coordination with the electrical wiring as they went. Dave also did some pretty spectacular template work to cut the boards around the van ribs and accommodate the fan and lights. We used 2 small trim screws to attach each board through its tongue to the furring strips in the ceiling and then knocked the next board into place.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*--kJRgtrIFquDnM9iUu2hQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*rwowRqVGS5tQiSWrP9dPFg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*m3ALrrHZ1q-R5LUwOI9aMA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*10DBfv8SNOb2dj4IkDDAZg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*P5texzI4dzZ3w7B7HjmJEg.jpeg" /></figure><p>The ceiling build in the end makes us a bit nervous — it’s a part of the van that would be truly very difficult to take down if we ever need to repair something. But for now we love the way it looks and feels!</p><h3>Upper Shelves</h3><p>While Dave and Spencer were installing the ceiling, I cut and fabricated the upper shelving. We debated going with hinging doors but in the end decided to keep it simple with open shelving — if we want to add doors later, we can! I built the frames and bottoms in the shop, installed them with screws into the furring strips behind the wall and bolts into T-nuts in the ceiling, and then cut and installed the side panels.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*W6EG5ar3-HLyKeA4AtSOoA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*7qdhTx8xeblnJctq6IbVww.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*AYhFfdImZIlXcJFXWwT_9A.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*kANd9DbghgdGWiCkGvedsQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*LjcY_7S56g35Ia9BNhtZkQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*dja1mIUeKFvDwqp7pT7glA.jpeg" /></figure><p>At this point we were getting super close!</p><h3>…</h3><h4>Ideas, advice, questions? Leave a comment below :)</h4><h4><a href="https://medium.com/vancilando/howdy-e226dc172b37">About Us.</a></h4><h4><a href="https://medium.com/vancilando">Back To Homepage.</a></h4><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=4b45150416e4" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/van-build-ceiling-upper-shelves-4b45150416e4">VAN BUILD: Ceiling + upper shelves</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[VAN BUILD: The soft stuff]]></title>
            <link>https://medium.com/vancilando/van-build-the-soft-stuff-2fcab80982a3?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/2fcab80982a3</guid>
            <category><![CDATA[sewing]]></category>
            <category><![CDATA[van-build]]></category>
            <category><![CDATA[vanlife]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Wed, 03 Jul 2019 18:45:53 GMT</pubDate>
            <atom:updated>2019-07-03T18:45:53.839Z</atom:updated>
            <content:encoded><![CDATA[<p>When Spencer and I hosted our wedding last September, we opted for canvas drop-cloth tablecloths rather than awful polyester rented ones for roughly the same price. It worked out really well for our camp wedding, and then we were left wondering what to do with all these drop-clothes!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*_YIs7Tk8R_7_T1S2S10JJQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*tUjodP3tlPr49OcZr4nXaA.jpeg" /><figcaption>Photos courtesy of <a href="https://www.instagram.com/sarahdodgephotography/">Sarah Dodge Photography</a>!</figcaption></figure><p>When we bought them, I had high hopes that we would re-use them for some cool project in the future, even if it was simply for their original dropcloth purpose. Little did I know we’d be dying them and reconfiguring them into various soft things for the van!</p><p>We spent a crazy weekend with my parents in Yorktown, my mom sewing pretty much nonstop for three days. We bought <a href="https://www.amazon.com/gp/product/B07LBZYP4M/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">2&quot; upholstery foam</a> and cut and sewed a cover to fit the bench seat. We had some extra, so we used it to make cushions for the back as well. We closed them with industrial velcro to make them easy to remove and wash. We then dyed the covers with liquid Rit Dye. We mixed some small batches first to get the proportions right before going for it with the newly sewn covers.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*JANI8ACt9VVooAnhnFvprQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*9Wn_UGrXLgCDFuRyPoih7g.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*k79PCZFzH2S1tU38uKKCwQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*nF5aknyzzKwrRRO3Jd2IEA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*4oZOuRPIejE5PCrEeI7laQ.jpeg" /></figure><p>Then we switched to the curtains, which we insulated using Thinsulate. These were significantly more challenging! But worth it in the end. We made inset covers for the back and sliding door windows, a rectangular cover for the side window, and two gigantic curtains to thermally separate the cab from the rest of the van.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*oY6MC_b84PvaM5Pl_fgPMQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*mUmvYvNMSu5aFAM0lC05hA.jpeg" /></figure><p>The strategy for the smaller window covers was to sew pockets for the Thinsulate, then dye the fabric, then insert the insulation into the pockets. For the gigantic curtains, we opted for sewing very long darts into the material after it was dyed, with a full roll of insulation in the curtain. This proved to be a bit too much for the sewing machine, but my mom wrestled them through with great determination while we cheered her on. We later installed snap-head screws in the plastic above the cab, which the curtains snap to. These have proved invaluable — the cab heats up so significantly and so quickly, plus the curtains allow us to create privacy very quickly by hanging them up. We like the snaps rather than a curtain rod scenario because then the curtains can be fully removed and laid on the bed when not in use!</p><p>We were planning on installing magnets in the other window covers in order to stick them to the van body, but instead used <a href="https://www.amazon.com/gp/product/B01L2TL60A/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">these mega magnet hooks</a> to simply stick them up! These are really handy to have around, so it worked out well in the end.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*1EuDZTjTduEhu7MKwf_sCQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*48Wdn2BswDWrXVH9hRLXxQ.jpeg" /><figcaption>Snap covers on the side window</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*50nS8QBS3NIrnrhkIpMS9Q.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*CxYJeQB3_aKiPA393B5HLg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Cr99f05VVopDRSggCYIh3A.jpeg" /><figcaption>Sliding door window covers with magnet hooks</figcaption></figure><p>In retrospect, this was a huge amount of work when we probably could have purchased something (ie, an insulated blanket) to reconfigure for not too much money. But it was a fun (if crazy) project and it felt good to reuse something from our wedding!</p><h3>…</h3><h4>Ideas, advice, questions? Leave a comment below :)</h4><h4><a href="https://medium.com/vancilando/howdy-e226dc172b37">About Us.</a></h4><h4><a href="https://medium.com/vancilando">Back To Homepage.</a></h4><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=2fcab80982a3" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/van-build-the-soft-stuff-2fcab80982a3">VAN BUILD: The soft stuff</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Marfa, TX]]></title>
            <link>https://medium.com/vancilando/marfa-tx-d4a2391a1655?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/d4a2391a1655</guid>
            <category><![CDATA[vanlife]]></category>
            <category><![CDATA[marfa]]></category>
            <category><![CDATA[texas]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Fri, 28 Jun 2019 19:38:13 GMT</pubDate>
            <atom:updated>2019-06-28T19:38:13.137Z</atom:updated>
            <content:encoded><![CDATA[<p>03/27–03/29</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*kcH5VJJz92mBKNBNHyf4Rw.jpeg" /></figure><p>Our stay in Marfa ended up being a bit of a life maintenance stop. Our travels through West Texas had thus far been very remote and even cell service felt novel and exciting. We spent almost our entire first day in town at the Tumbleweed Laundry, where they had laundry (obviously), coffee, ice cream, and wifi. I.e., pretty much everything we desperately needed!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*zONgxqcdiny5eHWiOPfG5w.jpeg" /></figure><p>After we got our lives together, we headed over to Capri where we ate some (small and expensive) appetizers and drank some (VERY tasty) margaritas. The highlight, however, was hands-down the mesquite bean ice cream, served in a GIANT frozen ceramic bowl, as recommended to us by Marfa resident friend Zeke, who we went to visit post-ice cream.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*nEQJNO0uOn4EG4BgR-0hag.jpeg" /></figure><p>We spent the night at the Marfa Lights pull off, where you can park overnight for free. It was beautiful to wake up to the desert sunrise.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*IljNxmVadKLtpSQDHNyy5A.jpeg" /></figure><p>The next day, we headed back into town to Do Your Thing for a coffee and some internet. In the afternoon, I headed to the Chinati Foundation for some art experiences with my parents — the sky was doing some very epic things (first picture), which definitely added to the experience. We didn’t time our visit very well, and were only able to see Judd’s concrete boxes, but it was still awesome. Watching the shadows change and move through them as the clouds rolled over was the best part!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*bNnTFZz5WWTNw4vA7iCboQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*BEN7b9zKx0LYCRzdZNXLVQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*mpylq3On6_z0Ln2pscjYrQ.jpeg" /></figure><p>For dinner, my parents took us out for a splurge at Cochineal which was totally delicious and amazing. Then Spencer and I parked on the street outside Do Your Thing — we discovered this is not prohibited in Marfa, which was very cool — where two other converted vans were also parked! Barring a few train interruptions, we had a good sleep and woke up to more DYT coffee. Then we headed into Big Bend!</p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=d4a2391a1655" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/marfa-tx-d4a2391a1655">Marfa, TX</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Davis Mountains State Park, TX]]></title>
            <link>https://medium.com/vancilando/davis-mountains-state-park-tx-5b5b6d526063?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/5b5b6d526063</guid>
            <category><![CDATA[vanlife]]></category>
            <category><![CDATA[travel]]></category>
            <category><![CDATA[texas]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Fri, 28 Jun 2019 01:15:50 GMT</pubDate>
            <atom:updated>2019-06-28T01:15:50.645Z</atom:updated>
            <content:encoded><![CDATA[<p>03/26, Site 67 | 04/01, Site 78</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*8yPBhnsLfwFNerpZcNheKg.jpeg" /></figure><p>We initially planned to stay at Davis Mountains State Park as a pit stop on our way to Marfa, but ended up loving it so much that we went back on our way from Big Bend to Hueco Tanks State Park. It was a surprisingly awesome campground, well laid out with beautiful strenuous hikes on the surrounding mountains.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*bq_jYPXXWZp6fwxoUH3v0g.jpeg" /></figure><h4>DAY 1 (3/26)</h4><p>We arrived on the afternoon of my birthday and got settled into our (very un-level) campsite. The sites were beautiful, it was the first time we had trees around us since Lost Maples. We went on a hike up the mountain, which we thought was going to be pretty low-key but ended up having way more elevation — we basically made it to the top of the mountain and had incredible 360 views all around us. We also had cell phone reception for the first time in DAYS, so ironically we hung out on top of the mountain to check in with friends and family for a while.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*HWFV9QTaKQu6Vky1qmFnfw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*w7LXdIRnVyq49mBbkqhMDA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*f7WIC5XfVrUp_KsZ6GXbhQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*CqA1k0-PW6iPMOps6hlp-g.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*dv71PCtBNxQR9pBReUnRqg.jpeg" /></figure><p>That evening, we headed to McDonald Observatory for a Star Party. It was looking pretty cloudy, and there were two epic thunderstorms coming in from either side of the sunset. We got up there early and made dinner in the van, had a birthday whiskey, and watched the sunset. The Star Party was awesome — way more people than I anticipated, but a really cool experience. We laid down on our blanket (as instructed by our friend, thanks Kylene!) to watch the guy give us the constellation tour with his mega powerful laser pointer. It started to get cloudier, so he sent us all over to the telescopes where we looked at several open star clusters. It made us want to buy a telescope (conveniently sold in their gift shop)…</p><p>We drove down the mountain in total darkness and went straight to sleep. In the morning, we checked out the bird blinds which were so cool — lots of great close views of birds feeding at the feeders and bathing in the pools.</p><h4>DAY 2 (04/01)</h4><p>Because we loved it so much the first time, we booked another night here as we were leaving Big Bend. This provided a much-needed shower stop and it felt surprisingly delightful to be in a familiar place. We also ran into a couple we met in Chisos Basin, who also have a converted van — they happened to be in the campsite right next to ours! We decided that despite its size, Texas is a small world.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*u3JAiwnFh2PZ_2jD008yAA.jpeg" /></figure><h4>BIRD LIST:</h4><p>Townsend’s Solitaire — White-winged Dove — Black-chinned Hummingbird — Acorn Woodpecker — Pine Siskin — Dark-eyed Junco — Canyon Towhee — Yellow-rumped Warbler</p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=5b5b6d526063" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/davis-mountains-state-park-tx-5b5b6d526063">Davis Mountains State Park, TX</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[Seminole Canyon State Park, TX]]></title>
            <link>https://medium.com/vancilando/seminole-canyon-state-park-tx-59789caf9fc?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/59789caf9fc</guid>
            <category><![CDATA[texas]]></category>
            <category><![CDATA[vanlife]]></category>
            <category><![CDATA[travel]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Fri, 28 Jun 2019 01:14:12 GMT</pubDate>
            <atom:updated>2019-06-28T01:14:12.246Z</atom:updated>
            <content:encoded><![CDATA[<p>03/21–03/26 | Site 45</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*T6HtxMZ_yhZ8ZekLuER3Cg.jpeg" /></figure><p>We arrived at Seminole Canyon around 5p on the 21st, got settled into our flower-filled campsite, and hung up our mosquito netting for the first time so we could sleep with the sliding door wide open. After camping at Lost Maples (during spring break), Seminole Canyon felt remote, quiet, and peaceful — even though most of the campsites were full.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*ntLHw6UMAO_-gm2tWJgDoQ.jpeg" /><figcaption>Site 45, view from the van</figcaption></figure><h4>WEATHER</h4><p>The weather was perfect for experiencing the West Texas desert — cloudy and misty in the morning, burning off sometime between 1p and 3p each day. We tried to get out and move around during the cloudy times and be back in the shade in the afternoon since the desert offered literally no protection from the sun.</p><h4>DAY 1 (3/22)</h4><p>Our first full day there, we biked the West Trail out to see Panther Cave, a cave painting across the Rio Grande only accessible by boat. We then biked a bit of the Canyon Rim Trail, which was beautiful and (as the name suggests) followed the rim of the canyon. Both trails were easy going, very little elevation, with beautiful views surrounding us.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*s-l1lGUW2Yg3iiiPl3R8CQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*WSysAKs1XT76LbDRf1iYEg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*OtH0BMjjXI_EQgihgUcNaQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*fv807fWt2HBEzzVYK3Sy0g.jpeg" /></figure><h4>DAY 2 (3/23)</h4><p>After a slow morning, I went for a 3-hour bird walk by myself while Spencer tied up a few loose ends in the van. It was an incredible experience to walk through the desert landscape alone — I saw only one other person the entire time, the solitude was all-encompassing. When I got back, Spencer had installed the tarp awning, which was crucial for staying cool in the Texas heat!</p><h4>DAY 3 (3/24)</h4><p>Spencer went on a bike ride in the morning while I hung out at the campsite and did some work. My parents arrived around 2p and we went on the Fate Bell cave tour to see the cave paintings below the visitor center. After biking and hiking on the rim for several days, it was awesome to be able to get down into the canyon. In the evening, while my parents got their camper settled, Spencer and I made a veggie curry and then after dinner we made a fire and had some amazing clear sky stargazing.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*0kLIAkNlJCkUN22zJMJswA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*6nEZuSQR2X1wxCMnegwQMw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*1pn7-X9SeJXmvc905alhiw.jpeg" /></figure><h4>DAY 4 (3/25)</h4><p>We went on a 4-hour bird walk with my parents. It was a pretty slow pace (lots of birds to see!!) which gave Spencer tons of time to document the ridiculous diversity of wildflowers (see below). When we got back, my parents moved to their campsite and got dinner going — a hearty lentil soup! We had some whiskey for my birthday, and lounged in hammocks at their campsite for a while before going back to ours to prep for our departure the following morning.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*h8SAfHiQMmQryfxeh_zxtw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*HPNyCi3boMYXBeLGRijLXg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*zPfk2dq40ojh93kuhNpuuQ.jpeg" /></figure><h4>FLOWERS</h4><p>The most magical part of being at Seminole was the wildflower superbloom they were experiencing. There were literally flowers <em>everywhere</em>, and so many different kinds. It made walking through the desert such a magical experience, with tiny glorious discoveries in every square foot of land.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*yHKsJ0q5p5oMK4k90ErsJQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*1PdfX1t2n76Yc_t5NSEemA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*DPvsXi_OYRS9ciIIO4DC0A.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*d9-Z5cHuBEGyP-15kIQvUw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*fEEduwbuCxs4IESI7Z73uw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*_pkuycsavufXYZgtfszlnw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*FxVjZgzCF4q-1CsExFX3Vg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Q7_W_AFdaL4U9DLMBOXBFw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Bydw79nSZ3rxOkE5CwO0Mw.jpeg" /></figure><h4>BIRD LIST:</h4><p>Common Poorwill — Great-horned Owl — Cactus Wren — Hooded Oriole — Great Kiskadee — Barn Swallow — White-throated Swift — Black Vulture — Turkey Vulture — Golden-fronted Woodpecker — Vermillion Flycatcher — Loggerhead Shrike — Northern Rough-winged Swallow — Canyon Wren — Blue-grey Gnatcatcher — Black-tailed Gnatcatcher — Northern Mockingbird — Cedar Waxwing — Cassin’s Sparrow — Black-throated Sparrow — Lark Sparrow — Lark Bunting — Canyon Towhee — Pyrrhuloxia</p><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=59789caf9fc" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/seminole-canyon-state-park-tx-59789caf9fc">Seminole Canyon State Park, TX</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[VAN BUILD: Furniture]]></title>
            <link>https://medium.com/vancilando/van-build-furniture-9131166e6e3d?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/9131166e6e3d</guid>
            <category><![CDATA[vanlife]]></category>
            <category><![CDATA[van-build]]></category>
            <category><![CDATA[diy]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Fri, 28 Jun 2019 00:57:58 GMT</pubDate>
            <atom:updated>2019-06-28T23:20:44.440Z</atom:updated>
            <content:encoded><![CDATA[<p>The furniture build out for this van was quite the undertaking. We started with the constraint that we wanted all connections to the van body to be bolted for strength and so we could remove the furniture in the future for repairs or renovations. The furniture broke down into three main modules — the wet module (sink + kitchen equipment), the power module (battery system), and the bench (with pull out Dometic fridge + large storage drawer).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*TmmbNzWzJlQlZo8F" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*LbwAUDvCFooGzjmI" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*oSa_30PTqIe2-M-a" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/0*nP_skd4hSGsvqYK6" /><figcaption>Wet module (L) — sink and plumbing, kitchen drawers, cooler drawer. Power + bench modules (R) — battery system, clothing storage, bench, Dometic drawer</figcaption></figure><p>Once the furniture frames were assembled, we installed cross-nuts in the aluminum frame which would allow a bracket to attach the frame to the floor. I machined these brackets out of 1X1X1/16 aluminum angle by drilling holes and cutting to length.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*iqSoIi7gHHSGSAijgjbMIg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*XxQgG3PiA96V8sZRCGYDLw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*eVgHlMAGbyTgUg9Xh0NdUA.jpeg" /><figcaption>Cross-nut installed in aluminum frame, machined bracket, mockup of attachment</figcaption></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*PfoM8vf0rsvoi3Hi8ipSaw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*I7bseYYWY1krGNAubeLjrQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*7ikd-TmoFcEeH_Xbs0ixlw.jpeg" /><figcaption>Bracket machining + installed position</figcaption></figure><p>After installing the cross-nuts and making the brackets, I fit and cut the stationary 1/2&quot; finish-grade plywood panels. These were later painted and installed, leaving the inside surface with its durable factory poly finish. A few panels had to be furred out to receive drawer slides, which was tricky to predict but worked out in the end with a bit of pre-planning.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*HuCmaxcWZJzDyJsvs8rUeA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*wJCjuuSuMdhDmVESFLCEzw.jpeg" /></figure><p>Next up was Drawer Mania. Our van has 6 regular drawers, 2 heavy duty drawers for the Dometic and cooler, and 2 hinged doors. Deciding to make the drawer faces inset and expose the aluminum frame added some tricky business to the drawer fabrication, as did the fact that we incorporated no horizontals between the individual drawers which would have made latching much easier. Lessons learned!</p><p>After making sure our drawers were sized for the things we needed to store in them, I laid out all the drawer dimensions, Dave wielded his skill saw with some mad Super Dave skillz, and we assembled the drawers using Kreg Jig pocket screws. The cooler drawers were more robust, using 3/4&quot; plywood with funny-shaped sides to allow access to the handles and to make removing them easier. I then painted all the drawers with two coats of paint and laid out the drawer slides. Once the drawer slides were installed, I test fit all the drawer boxes in the furniture.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*1kV2uW-x0qOp8VaMN-7pLA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*ZdBiDWWdp8ah8Nu6k2_x4Q.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*roetvwCbUFbdY578WPkjbQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*tpVCov0QF4JDhmS8BSEZJw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*ZmOAoqYHSc8-hJXI3h6vFw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*dQByE2Y-OgWD4D4wKnhcqA.jpeg" /><figcaption>DRAWER MANIAAAAA</figcaption></figure><p>The next step was to work on the bench construction. We decided on a slightly sloping back for comfort and wrestled our slightly out of square aluminum frames into submission. This part was pretty tricky and in the end we decided to attach a back panel to link the power and bench modules together for additional support. We remembered to cut a hole for the Dometic plug just in time! And of course had to immediately test out the cushions to celebrate the milestone.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Do1Xh8e1lS36qmNrORwdXA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*-De9I9l_ZpzFueB5mk4Eig.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*fr62ydatZvh8c6ToWVWW-Q.jpeg" /></figure><p>We then turned to the countertops. We had decided on laminated wood, after thinking through several other options which all seemed heavier and more expensive. Our first version was laminated plywood, which ended up being totally ugly and awful. Good thing the lumber yard in Powhatan had an incredible selection of tight-grained pine, because that version was so much better! We ripped the boards on the tablesaw to width and then glued them together with one million clamps. The countertops were then cut to length and planed with a hand plane to get the major bumps and glue oozes off, followed by many hours of incremental sanding (THANK YOU DAVE!!). We cut a template for the sink, then cut the hole and test fit the sink and faucet. I then sealed the counters with several coats of polycrylic and sanded in between with fine steel wool. We were super stoked with how they turned out!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*MVjD_GjIuAGckn8tsguSSA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Z1QOqsUo-E-RrXDMam5lVg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*h-eU2QU0p_c_C6i4RKolZA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*2uOUeOaHyglsbaobelXOoA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*DcG2k3UfQZ4w-2oO5oColw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*uaUXoS1pL_abw5Os3csgxg.jpeg" /></figure><p>After assembling 90% of the furniture and removing the drawers, we installed the frames in the van by bolting them to pre-installed T-nuts in the floor. We were nervous about alignment, but to our surprise and relief, our templates and remeasuring paid off and the holes in the brackets had just enough wiggle room to align all bolts perfectly. We also installed the countertops with corner brackets from underneath which was a fun challenge.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*iLpTtg1Y5-A2BScf6uHraA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*a8mO6qFYZmQa1deZxO86ZA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*A9JCst36V0L_1AyjIErWJQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Ja_k6i8Rf5Qd3sD0Y11s3w.jpeg" /><figcaption>We were very excited about getting the furniture installed and had to celebrate with a sit on the bench! And a few bourbons.</figcaption></figure><p>The next day, we installed the sink (see plumbing post) and I installed the drawer faces using a deck of cards for shim space and a nail gun. Then, the drawers were removed again, the faces painted and hardware installed. We also installed the inset hinges for the two doors and found some magnetic latches to hold them closed. At this point we were really coming down to our deadline for getting on the road, so I didn’t take many pictures!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*o4vUBZSZ-C7nVWCbnNP_Ew.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Op1hWbhlAkbAwmOVb3FeQQ.jpeg" /><figcaption>NEARLY THERE!!</figcaption></figure><h3>…</h3><h4>Ideas, advice, questions? Leave a comment below :)</h4><h4><a href="https://medium.com/vancilando/howdy-e226dc172b37">About Us.</a></h4><h4><a href="https://medium.com/vancilando">Back To Homepage.</a></h4><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=9131166e6e3d" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/van-build-furniture-9131166e6e3d">VAN BUILD: Furniture</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[VAN BUILD: Walls]]></title>
            <link>https://medium.com/vancilando/van-build-walls-81596889191f?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/81596889191f</guid>
            <category><![CDATA[van-build]]></category>
            <category><![CDATA[diy]]></category>
            <category><![CDATA[vanlife]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Fri, 28 Jun 2019 00:55:40 GMT</pubDate>
            <atom:updated>2019-06-28T00:55:40.518Z</atom:updated>
            <content:encoded><![CDATA[<p>Once the wall insulation was in, we turned our attention to the walls themselves. This was one of the trickiest parts of the build, with many head-scratching moments as we tried to figure out how to create a flat surface within a very out-of-square, bumpy metal box.</p><p>We debated many strategies for approaching this and in the end, went with 1/4&quot; finish ply. For the lower walls, we decided to attach the panels directly through T-nuts installed in the pre-existing holes in the van body and let the panels be inset, exposing the metal ribs. For the upper more visible portions of the walls, we furred out the surface everywhere except the bed, where we inset the panels to allow for a critical extra 2&quot; of width.</p><p>Prior to installing the wall panels, we used <a href="https://www.amazon.com/gp/product/B000CQG1U0/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">Thinsulate</a> to insulate the funky shapes of the van — inside the structural ribs, in weird corners, and in the hollow portions of the doors. This process was pretty enjoyable — the Thinsulate was very easy to cut with scissors, and I used a metal coat hanger to feed it through the ribs. The rear wheel wells were insulated using <a href="https://www.amazon.com/gp/product/B00PX2C8DC/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">EZ-Cool insulation</a>, adhered with spray adhesive.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*grDcD82vh4hA9_5brfYvuw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*saSk-9eGGFo2rn85HYELeA.jpeg" /><figcaption>Thinsulate-ing the funky spaces</figcaption></figure><p>After insulation was complete, we primed all the 1/4&quot; plywood sheets to make our jobs easier down the line. Next we installed <a href="https://www.amazon.com/gp/product/B008VGWFAI/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">cross-nuts</a> in the factory holes of the van, adding more holes where we needed additional connection points. We would highly recommend buying <a href="https://www.amazon.com/gp/product/B01CUL8D9G/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">this installation tool</a> — it made the installation process much easier and we were thankful we spent the money for it, especially after installing exactly 100 cross nuts in various places in the van!</p><p>Next up was making templates for the lower wall panels, which Dave crafted out of thick construction paper. We then cut the panels, located and drilled the cross nut holes and did a test fit. We set these aside for their finish coat of paint.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*CjkFDCvgxMCeVOvIC1XZWQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*YobNnsUHQFHIPCXsoiqqYA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*IV5uCm1HiTVDoGCKcGMM4g.jpeg" /></figure><p>Furring out the upper walls was an exciting adventure. We used some leftover cedar 2x’s Dave had in the shop, so we didn’t have to seal them. We aimed to create as flat a surface as we could, with bump-outs for the window and either side of the bed. The bump-outs were built as units that were then installed, with the outer layer of 1/4&quot; ply coming in last. Before doing the final install on these pieces, they received two coats of Behr white paint on the outside face and we sealed the back side to prevent moisture absorption.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*WwJlBVLDJyHAjLg_6SVoCw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*QL2AaRaxyAz-COaxB32qSg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*9yIwUijoyncb5nbibNJ61Q.jpeg" /></figure><p>The final task was to attach the plywood to the bump-outs and furring strips. This gave us a bit of heartache, because we ended up using a nail gun instead of screws. It definitely provides a cleaner finished look, with fewer fasteners scattered throughout, but it means if we ever want to change anything or repair something behind the wall we’ll be prying it off — a process it probably won’t survive. But nail gunning the walls on definitely took very little time and allowed us to finish the build on our planned schedule! Where the panel attached to the area around the window, we used snap-head screws to attach it so we could snap our curtain in place down the road.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*PpnQ-iFiGjAVTxNPD6f2hA.jpeg" /></figure><p>In a few places, we used <a href="https://www.amazon.com/Parts-Express-Speaker-Cabinet-Carpet/dp/B0002ZPNKA">automotive carpet</a> to tackle the odd geometries of the van body. This was primarily around the back and sliding doors, where the metal would have been prominently exposed. Installing the carpet, while tedious, was pretty straightforward and we found ourselves wishing we had used this in a few more places instead of trying to making the paneling work.</p><p>We learned a very important lesson during this process: do NOT paint the backside of a wall panel with anything glossy. If it touches metal, it will squeak as you drive down the road. We learned this with sinking hearts as we backed out of the driveway, but it didn’t impact anything structurally and the squeaks have diminished significantly as the paint cured over time. If we were to do it again, we would avoid painting these surfaces with semi-gloss and we would likely use a piece of underlayment to prevent the surfaces from touching in the first place.</p><h3>…</h3><h4>Ideas, advice, questions? Leave a comment below :)</h4><h4><a href="https://medium.com/vancilando/howdy-e226dc172b37">About Us.</a></h4><h4><a href="https://medium.com/vancilando">Back To Homepage.</a></h4><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=81596889191f" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/van-build-walls-81596889191f">VAN BUILD: Walls</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[VAN BUILD: Fan]]></title>
            <link>https://medium.com/vancilando/van-build-fan-installation-732f3b83f45d?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/732f3b83f45d</guid>
            <category><![CDATA[van-build]]></category>
            <category><![CDATA[diy]]></category>
            <category><![CDATA[vanlife]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Fri, 28 Jun 2019 00:33:32 GMT</pubDate>
            <atom:updated>2019-06-28T16:58:37.306Z</atom:updated>
            <content:encoded><![CDATA[<p>One of the first things we did after insulating the van and installing the window was install our <a href="https://www.amazon.com/gp/product/B003ZOF09Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1">Maxxair fan</a>. We had to wait for good weather, which finally came around so we could get up on the roof and have warm enough temperatures to cure the various adhesives and sealants. We also had to time it so we wouldn’t need to bring the van back into the shop — it most definitely would not fit after we added the additional fan height!</p><p>The first step was to locate and jigsaw the hole in the roof, which went really smoothly. We made sure to tape up a garbage bag on the inside so tiny metal shavings didn’t get stuck all over the inside of the van!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*7g5RvS1JfRMwkzHY32vkJg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Peq5XOLF_xMDtI1h62RkEA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Z1gTgNPwuN7siirOBi1MdA.jpeg" /><figcaption>Cutting the roof hole!</figcaption></figure><p>While Spencer sorted things out on the roof, I machined some aluminum struts to stiffen the plastic rim of the fan — a pro tip suggested on several blogs we read.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*VS6fp-RH0AEMqTyL7MqLig.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*qrSJN0mJ5EXimiBwS5mlKw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*DWJ9L78W1qLbMI40-Bqylg.jpeg" /><figcaption>Machining and fitting aluminum struts to the fan flanges</figcaption></figure><p>We then installed the <a href="https://www.ebay.com/itm/142478235445">roof vent adapter</a>, which provides a level surface to receive the fan flanges.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*5M1tCvE9Y6R-6V61yk9daQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*SRmnpyh783YXw_do-Aq3SQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*jVneE_-OPvbjUXYwzoomlQ.jpeg" /><figcaption>Gluing the roof vent adapter to the roof (and witnessing THE HAND OF GOD)</figcaption></figure><p>We used a marine adhesive sealant to adhere the fan flanges to the roof vent adapter, then screwed through the flanges to the body of the van with sheet metal screws, and covered the whole shebang with self-leveling sealant — a crucial step for providing a complete seal over the various screw holes. The overall result was definitely a bit goopy, but confidently leak-proof (knock on wood…).</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*OBa1sHGLxgIJ3-k0fspgdg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*YLNfwNr9hrOf8kvvGRnwVQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*vG5dNi196l0ewyybwzffsA.jpeg" /><figcaption>Various sealants we used to install the fan</figcaption></figure><p>The next step for the fan install was to hook it up to our power system !</p><h3>…</h3><h4>Ideas, advice, questions? Leave a comment below :)</h4><h4><a href="https://medium.com/vancilando/howdy-e226dc172b37">About Us.</a></h4><h4><a href="https://medium.com/vancilando">Back To Homepage.</a></h4><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=732f3b83f45d" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/van-build-fan-installation-732f3b83f45d">VAN BUILD: Fan</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
        <item>
            <title><![CDATA[VAN BUILD: Window & insulation & swivel seat]]></title>
            <link>https://medium.com/vancilando/window-prep-insulation-swivel-seat-furniture-frames-178b33803ac7?source=rss----4a4b65ac3c80---4</link>
            <guid isPermaLink="false">https://medium.com/p/178b33803ac7</guid>
            <category><![CDATA[diy]]></category>
            <category><![CDATA[design]]></category>
            <category><![CDATA[vanlife]]></category>
            <dc:creator><![CDATA[Clare van Montfrans]]></dc:creator>
            <pubDate>Wed, 23 Jan 2019 17:02:32 GMT</pubDate>
            <atom:updated>2019-06-28T01:08:06.257Z</atom:updated>
            <content:encoded><![CDATA[<figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*l7f8QWVqgsEwhpv9O7gwhg.jpeg" /></figure><h3>VAN BUILD: Window prep, insulation, and a swivel seat.</h3><p>We’ve been in Powhatan VA staying with Spencer’s parents for about two weeks now, and we’re finally starting to see some results in the Merry Weather. Because we’re both working full time remotely, it took us a while to work out the schedule for van projects but with two big building weekends behind us, we’ve now gotten into the swing of things with visible progress.</p><p>The very first step was to squeeeeeeeze the van into Dave’s shop — a tight fit, but we managed to get it in there! Definitely not much room for other things, but it’s been SO nice (as temperatures dipped down to 11 degrees…) to have the wood stove heat while we’ve been slowly puzzling over interior questions.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Z_MJXdureDhumgx_4Pmqiw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*rgDjqzyuVPIhasUWqTroXg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*l0dT-rFiPJvb6MrJ6KnJNQ.jpeg" /><figcaption>It was a tight fit, but we made it!</figcaption></figure><h3>Window Prep</h3><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*hgGhG72fZXwgzPuV1z8cXA.jpeg" /></figure><p>The most horrifying task so far was cutting the hole for the new window on the driver side of the van. We ordered this window from <a href="https://www.motionwindows.com/ram-promaster-van-conversion-windows/">Motion Window</a>— the first step was to make a template to trace onto the wall of the van. Why it doesn’t come with one beats me! But we managed to get a fairly accurate template cut out and drawn onto the van. Spencer jigsawed the hole with serious accuracy and concentration — it felt very scary to be poking such a gigantic hole in the side of a vehicle, but it went really well. It’s not the last hole we’ll have to cut in the exterior of the van, and hopefully the rest will go this smoothly. We’ll be installing the window this week and will share final pictures once it’s in!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*1B6Lttm3imflaRb9VQBevw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*bLhnI__u-ciN8H9tIs6Bkw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*Od5IFH92E-uvCGqQ_-iicQ.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*6AgHvCRfa3QstSEgger9Tw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*NbfObD_5u6rdzjP0YHe9ew.jpeg" /></figure><h3>Insulation</h3><p>One of our first big tasks was insulating the van. We used 4 sheets of 1&quot; rigid poly iso to insulate the walls and ceiling. We cut all the panels to size with a box cutter, which took quite a bit of back-and-forthing to accommodate the van’s funky corners, and then began to glue them into place using Great Stuff gap filler foam. This worked well to stick them in place and then it expanded slightly after we stuck the panels to the wall, creating a tiny air gap which will help the insulating layer do it’s job. All in, this part took us a solid Saturday to get it all in. We have a few more insulating tasks ahead — adding 1&quot; Thinsulate inside the ribs and 1/4&quot; closed cell foam to any areas where the wall will be tight to the metal surface.</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*GO5AQbbC4nei64OL3qz8MA.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*j7_v_CpZbaUvZLmocac2sw.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*wICg7nhgVCo8d2gvtGu_hg.jpeg" /><figcaption>Cutting and foaming in the poly iso</figcaption></figure><h3>Swivel Seat</h3><p>I think the most exciting accomplishment was installing the swivel seat. We were expecting this to be a very arduous task, based on reading other van conversion blogs, but Dave and Spencer got the passenger seat removed, installed the new swivel adapter, and reinstalled the seat in a record-breaking 45 minutes! It was such a satisfying success, and the impact on the experience of the van was HUGE. The whole interior feels much more open and we immediately started talking about installing a driver side swivel. One step at a time though, they’re pretty pricey — so we’ll test drive this one first for a while!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*hL9dlHhtMssovHiNi9DAww.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*lERUFTlpc1Asn7jIpFsc0Q.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*MBhkt6VPfDhyw6qQmohpMA.jpeg" /></figure><h3>Furniture Framing</h3><p>My favorite part this week has been assembling the furniture framing. We wanted a system that was strong and rigid, yet lightweight, and aluminum met both of those needs. After doing some research, we opted for 1&quot; aluminum square stock and connectors from ESTO. In getting the components quoted, I realized it would only be $30 extra to get the pieces cut to length, so we went for that upgrade. This meant we had to have the model pretty well resolved before ordering, which was nerve wracking but fun. This week I assembled all the pieces with a rubber mallet and we now have 3 furniture frames sitting in the van, awaiting their cabinetry inserts!</p><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*b6wExudJ2NEP15pkkkktjg.jpeg" /></figure><figure><img alt="" src="https://cdn-images-1.medium.com/max/1024/1*6YqyaKrTmRAZYcOSgd_uww.jpeg" /><figcaption>Furniture framing taking shape</figcaption></figure><h3>Next up: working out the cabinet hardware, the floor mounting strategy for the furniture modules and spec’ing the electrical system!</h3><h4>Ideas, advice, questions? Leave a comment below :)</h4><h4><a href="https://medium.com/vancilando/howdy-e226dc172b37">About Us.</a></h4><h4><a href="https://medium.com/vancilando">Back To Homepage.</a></h4><img src="https://medium.com/_/stat?event=post.clientViewed&referrerSource=full_rss&postId=178b33803ac7" width="1" height="1" alt=""><hr><p><a href="https://medium.com/vancilando/window-prep-insulation-swivel-seat-furniture-frames-178b33803ac7">VAN BUILD: Window &amp; insulation &amp; swivel seat</a> was originally published in <a href="https://medium.com/vancilando">vancilando</a> on Medium, where people are continuing the conversation by highlighting and responding to this story.</p>]]></content:encoded>
        </item>
    </channel>
</rss>