Runways
If you’ve ever been on a flight, you must be familiar with the takeoff and landing at least (except you’re a skydiver who doesn’t bother about landing with the plane). However, a really important piece in the puzzle of takeoff and landing is the runway. You’ve probably noticed how the plane lines up on a straight stretch of pavement and speeds up before flying, or how it lands on a similar pavement and slows down.
What is a Runway?
Runways are rectangular stretches of land prepared for aircraft to land and takeoff. Essentially, they provided a reasonable level and long enough surface for airplanes to get to high speeds or slow down from high speeds on the ground. While most runways are made of asphalt or concrete, this is not always the case.
So, What Are Runways Made Of?
The decision on which material to use for a runway’s construction depends on several factors, including soil conditions, weather, available materials and expected aircraft type. For heavier aircraft, it makes sense to use a strong material like concrete or asphalt, just as used in road construction. However, light aircraft (the likes of small 4 seat propeller planes) can do just fine with grass or dirt runways. It is important that the ground be firm enough though, so that the wheels do not dig into the ground and potentially tip the plane over. In essence, a runway is limited by its load bearing capacity. Another interesting and rather unusual material used for runway construction is ice. Yes, solid water. The most common example of an ice runway is one close to the McMurdo Station in Antarctica. Other interesting materials used to make runways are clay, gravel, coral, etc.
Water runways (liquid water) are an interesting phenomenon. Generally, they are used in island settings where land is a luxury that is not readily available. Unlike other runways that planes can land on with wheels, water runways are only accessible to aircraft mounted with floats.
Constructing Runways
Early aviation was rather simple when it came to runways. All that was needed was usually a patch of level ground with a decent length. This worked well because early airplanes were rather light relatively slow. As the concept of flying boats and float planes began to take hold, airPORTS began to sprout around bodies of water. This strategic positioning allowed planes to be accessed easily by passengers, complete with shoreside service.
Get Daniel Dikio’s stories in your inbox
Join Medium for free to get updates from this writer.
Modern runways can be several kilometers long, over a hundred feet wide and a couple of inches deep. This type of project requires a lot of materials, compressed uniformly and well reinforced to bear the weight of large airliners. Constructing a new runway can easily cost hundreds of millions of dollars, and this is not just because of the concrete or asphalt. Runways also have enhanced drainage systems to get rid of water as quickly as possible, along with specialized lighting that must meet prescribed standards.
Runway Dimensions
In actual practice, this is no specific dimensions that a runway must conform to. Accordingly, runways can be as short as 245m (804ft) and as long as over 5,000m (16,404ft). Similarly, runway widths vary from 8m (26ft) to up to 274m (899ft). Ultimately, the design dimensions of a runway are determined by the size of aircraft it is expected to serve. Big runway = big aeroplane. Thickness is based on the weight of expected aircraft and the underlying soil composition. More stable soils will require runways of less thickness that soft, unstable soils.
Big Numbers On Runways
If you are observant enough, you may have noticed that runways usually have big numbers painted on them. These numbers run from 1 to 36 and perform a critical function, they indicate the runway heading. For the purpose of simplicity, the runway heading is approximated to the nearest ten and then divided by 10. As such, a runway with a bearing of 280 degrees and another at 276 degrees are actually going to have the same number, 28. Runway orientation is generally determined by the prevailing wind directions, except where a more pressing constraint like terrain takes priority. So long as terrain is not a concern, planes can usually take off from either direction of the runway, making each strip of runway to be two runways, both numbered. Following the previous example, the other end of the runway will be 10 ((280–180)/10).
Since runways that oriented in the prevailing wind direction(s), it is not unusual for an airport with several runways to have two or more parallel to each other. In cases where there are two parallel runways, the one on the left become L and the right become R (how smart). An airport like Heathrow has runways 27L and 27R, and from the other end, runways 9R and 9L. When three runways are involved, the extreme runways retain their L and R designators while the one in the middle becomes C (for center). Therefore, an airport like Amsterdam Schiphol has runways 18L, 18C, 18R and from the other end, runways 36R, 36C and 36L. On some occasions, there may be even more than just three parallel runways. Los Angeles International Airport has four parallel runways. To solve the challenges that could be posed by this numbering dilemma, a pair of runways have their numbers offset. This gives runways 24L, 24R, 25L, 25R and from the other end, runways 6R, 6L, 7R and 7L.
There is a lot more to discover about runways and I look forward to taking you on another discovery soon.
See ya.








